Current location - Recipe Complete Network - Catering franchise - Training Report Training Contents 12
Training Report Training Contents 12
# Internship Report # Introductory training includes on-campus training and off-campus training, including teaching training, teaching training and production training. From the content, there are practical skills training and mental skills training; Including comprehensive quality requirements (entrepreneurial ability and employability are collectively referred to as cross-post ability) training. This article is a training report for you from 12. I hope I can help you. Welcome to share!

1. Training Report Training Contents

1. group preparation: students are free to form groups of 3-4 people and cooperate with each other. 2. Survey preparation: Students collect relevant information about the enterprises under investigation.

3. Investigation on the cognition of commodity circulation: investigate the circulation enterprises. Check its store location, store layout, merchandise display, customer service, etc.

4. Summary and evaluation: Write down your experience and activity report.

This training lasted for 5 days, with different contents and tasks every day. We can combine freely. There are four members in our group. On the first day of training, the training task: collect the relevant information of Shiqiaopu xx supermarket to prepare for the field investigation of xx supermarket. The next day's task: continue to collect information, but make a research report, list the contents of a simple survey, and conduct a targeted survey. Our group intends to investigate from seven aspects: 1) supermarket location 2) commodity price 3) business model 4) commodity display 5) independent brands 6) commodity types. The third day: We came to xx supermarket for field research. Under the guidance of the staff, we visited warehouses, shops and other places. We know the process from receiving goods to entering the store (receiving goods, commodity acceptance, turnover, stocking, entering the store and returning goods). Xx supermarket implements the closed management of the picking process and the closed management of the inventory process.

Training content: Make the relevant information we know about xx supermarket into PPT. The PPT content of our group can be roughly divided into seven aspects: 1) supermarket profile 2) supermarket site selection 3) business scale product display: best-selling products are placed in the most conspicuous place 4) warehouse management 5) product types 6) own brand 7) training summary.

2. Training Report Training Contents

Garden tree cultivation refers to a long process of cultivation practice from seedling emergence to tree decay and renewal. The cultivation level of garden trees directly affects the role of trees in garden greening construction. The growth and development of garden trees, especially the natural or artificial plant community with trees as the main body, has obvious comprehensive benefits of improving the environment, viewing, recreation and economic production. Therefore, the training of garden tree cultivation and maintenance is very important. We are also very serious about this tree transplant. Through the explanation of teachers and technicians, we also mastered some methods of tree transplantation. Tree transplantation refers to tree transplantation with DBH greater than 15cm. Transplanting big trees can quickly achieve the effect of greening and beautifying gardens, and it is also an effective means to protect ancient and famous trees and existing big trees in urban reconstruction and expansion projects.

The teacher divided the group members well, and each group dug the designated seedlings with hoes. We are osmanthus trees, and the DBH is about 8- 10 cm. Before transplanting, we first remove the topsoil around the trunk to reduce unnecessary earthwork. Draw the boundary line of the soil ball, dig an operation ditch outside the soil ball line, dig down, and cut off the lateral roots with a shovel and a hand saw. The shape of the soil ball should be large and small, gradually starting the line and closing the bottom, and finally cutting off the main root. Repair the ball to make it symmetrical and even around. The spherical surface is compact and complete, the crack root should be short and the incision should be smooth. Ensure that the soil ball of trees is 8 ~ 10 times that of seedlings, and the thickness of soil ball is not less than 2/3 of the diameter of soil ball. When digging, you can use a sharp saw or shovel to saw off the thick roots.

When the straw rope is used, it will not come loose, and then it will be pulled from 1 to 2, bypassing the bottom of the soil ball to 4, bypassing the bottom of the soil ball to 6, bypassing the bottom of the soil ball from 7 to 8, bypassing the bottom of the soil ball, and passing through the surface of the soil ball from 9 to 10, according to the numerical order shown in the figure. In this order, it is next to Pinza's 6-7 pentagrams. The package should be dense and firm to prevent the soil ball from cracking. In order to facilitate excavation, prevent branches from breaking and improve the survival rate of seedlings, crown pruning should be carried out at the end of the transplanting process to reduce water transpiration of trees and ensure their survival. Pruning should be based on the principle of maintaining the original crown shape. Too dense main branches and side branches can be properly thinned, and the remaining side branches can be appropriately shortened, or some leaves can be removed.

3. Training Report Training Contents

Taking the actual economic business of an enterprise as the training material, and using the vouchers and accounts in accounting work, this paper makes a systematic operation experiment on each step of accounting, including the establishment of account books and the filling of the balance at the beginning of the month, the examination and filling of original vouchers and accounting vouchers, and the registration, reconciliation and closing of various account books.

4. Training Report Training Contents

During the training of thoracic surgery, with the help and guidance of teacher xx, combined with my own practice, I mastered the rules and regulations of thoracic surgery, carefully studied the specialized nursing operations such as venography puncture, strictly adhered to the aseptic operation principle required by thoracic surgery, and further standardized and mastered the basic nursing operations such as intravenous infusion, subcutaneous injection and intradermal injection. Seriously perform the duties of training nurses, be strict with yourself, respect teachers, unite with classmates, care for patients, never be late, never leave early, work hard, try to standardize nursing work, combine theory with practice, always take "love, care and patience" as the basic in training, and strive to provide quality services to patients wholeheartedly and strictly implement the "three 5s". Training report training content

According to the relevant international trade laws and practices, combined with China's actual situation and international trade practices, taking the basic process of export trade as the main line and the simulated specific export commodity transaction as the background, aiming at the main business operation skills in export trade, such as drafting business letters and telegrams, accounting commodity prices, negotiating trade terms, signing sales contracts, booking shipping space for export goods, customs declaration, examining letters of credit, making and examining trade documents, etc.

6. Training Report Training Contents

(a), foundation slab and foundation beam steel binding 1. According to the pop-up reinforcement position line, the lower reinforcement shall be laid first. According to the stress of the bottom plate, decide which direction the lower reinforcement is below. Generally, short tendons are laid first, and then long tendons are laid.

2. Put the mortar pad of the concrete protective layer of the bottom plate, the thickness of the pad is equal to the thickness of the protective layer, which can be reduced by the distance of 1m or so, and even the mortar pad can be replaced by iron.

3. If there is a foundation beam on the bottom plate, it can be bound and shaped in sections and then installed in place, or it can be bound and shaped on the spot according to the beam position line.

4. When there are binding joints for floor reinforcement, the lap length and lap position of reinforcement shall meet the requirements of construction specifications, and the lap joints of reinforcement shall be fastened with iron wires at the middle and both ends. If welded joints are used, in addition to sampling according to the welding regulations, the joint position should also comply with the construction specifications.

5. According to the played position line of the wall column, the steel dowel inserted into the foundation of the wall column should be firmly bound, the depth of the inserted foundation should meet the design requirements, and the length of the sling should not be too long. Measures should be taken to ensure that the sling is vertical and will not be skewed, dumped or displaced.

(2) Binding of beam reinforcement

1. Draw the stirrup spacing on the beam side formwork and place the stirrups.

2. First, pass through the longitudinal stress reinforcement and bending reinforcement at the lower part of the main girder, and separate the stirrups one by one according to the drawn spacing; Wear the longitudinal stressed steel bars and bent steel bars at the lower part of the secondary beam, and set stirrups; Put the scissors of primary and secondary beams; Tie up the installation stud and stirrup at regular intervals; Adjust the spacing of stirrups to meet the design requirements, tie vertical bars, then tie main bars, and coordinate primary and secondary beams at the same time.

3. The upper longitudinal reinforcement of the frame beam should run through the middle node, and the anchorage length of the lower longitudinal reinforcement of the beam should meet the design requirements.

4. The stirrup hooks at the lap joint are staggered and bound in the beam. The stirrup hooks are 135, and the length of the straight part is 10d. If the closed hoop is made, the length of one-sided weld is 5d.

5. The first stirrup at the beam end should be set 50㎜ away from the edge of column node. The stirrup at the joint of beam end and column should be encrypted to meet the design requirements.

6. Lapping of beam reinforcement: When the diameter of the stressed reinforcement of the beam is equal to or greater than 22㎜, welded joints shall be adopted; When it is less than 22㎜, binding joints can be used, and the lap length should comply with the regulations. The distance between the end of the lap length and the bend of the steel bar should not be less than 10 times the diameter of the steel bar. The joint should not be located at the bending moment of the member. In the tension zone, the ends of the binding joints of Grade I steel bars should be hooked (Grade II steel bars are not hooked), and the lap joints should be fastened at the center and both ends.

(3), plate steel binding

1. Clean up the sundries on the template, draw the main reinforcement on the template with chalk, and allocate the spacing between the reinforcement.

2. According to the planned spacing, put the main reinforcement first, and then put the distribution reinforcement. Embedded parts, electrical conduits and reserved holes shall be installed in time. Two-way stress plate, short-term reinforcement below, long-term reinforcement above.

3. When the cast-in-place slab has a slab beam, the slab beam reinforcement shall be bound first, and then the slab reinforcement shall be placed.

4. Place mortar pads under the steel bars with the spacing of xxm. The thickness of pad is equal to the thickness of protective layer, which should meet the design requirements. When there is no requirement in the design, the thickness of the protective layer of the slab should be 15㎜, and the requirements for the lap length and lap position of reinforcement are the same as those of the beam mentioned above.

7. Training Report Training Contents

Precautions during processing: a. Be sure to concentrate on your work and don't leave the machine without authorization.

B, the workpiece and turning tool should be clamped firmly, so as to avoid the workpiece and turning tool flying out and hurting people.

C, workpiece rotation, are not allowed to measure the workpiece.

D, after the workpiece is installed, the three-jaw wrench must be removed, so as to avoid accidentally starting the lathe, so as to avoid the wrench flying out and hurting people.

1. Material taking: according to the requirements of drawings, 45-grade steel bars with φ 32 and 100㎜ are selected.

2, according to the drawing requirements for blank selection and processing sequence.

3. Tool installation: Use a tool wrench to twist the screw on the tool holder, and put the 90 hard right deviation tool into the tool holder with a right deviation of 65. Use the height of the center head to adjust the height of the tip. After adjustment, tighten the screws on the tool rest with a tool wrench. The installation method of the cutting knife is the same as that of the 90 hard right deviation knife. After the tool is installed, tighten the handle on the tool rest to fix the whole tool rest, so as to avoid the tool rest from loosening during processing, which is not conducive to cutting.

4. Installation material: loosen the three-jaw self-centering chuck with the three-jaw key and clamp the material. Then tighten the self-centering chuck with the three-jaw key and remove the three-jaw key. Start the machine to check whether there is swing phenomenon when the material rotates. If there is swing, please turn off the machine and adjust the material. After adjustment, start the machine to check whether the material still swings. No processing can be carried out before the material rotates and swings.

5. Prepare tools to be used in processing, such as vernier calipers and drawings, and put them in convenient places for easy use.

6. Prepare to start completely machining the blank and conduct process analysis. The processing sequence should be rough machining, semi-finish machining and finish machining.

7. Due to the high machining accuracy of the stepped shaft, it is necessary to stop the machine continuously during the machining process, and measure the size with vernier calipers to ensure the size requirements. When the workpiece rotates, you can't measure the size, and you can't touch the workpiece with your hands, so as not to damage the vernier caliper and hurt your hands.

8. After the workpiece is cut, turn off the machine tool, wait for the workpiece to stop naturally, and then use vernier caliper to measure according to the size requirements on the drawing. After the size is correct, the cutter changer cuts a groove at the cutting position when starting, and the front end and the back end are chamfered. Then cut off the workpiece and stop the machine.

9. Mark the keyway of the rotating stepped shaft with a marking needle and a ruler.

10. Loosen the screw that fixes the workpiece on the milling machine with adjustable wrench, clamp the workpiece, and position the horizontal and vertical workpiece tables on the milling machine. After positioning, start the milling machine for keyway milling.

8. Training Report Training Contents

Taking the annual accounting statements of enterprises as training materials, the risk-oriented audit mode is adopted to carry out the system operation experiment, including accepting the entrustment of the audited entity, signing the business engagement letter, compiling the overall audit strategy and specific audit plan, and using the main audit procedures such as checking records or documents, checking tangible assets, observing, inquiring, confirming, recalculating, recalculating, executing and analyzing procedures, collecting sufficient and appropriate audit evidence and compiling audit working papers. Finally, organize, analyze, identify and summarize the audit evidence, form appropriate audit opinions and issue audit reports.

9. Training Report Training Contents

Practice computer hardware assembly in groups, learn the use of common tools and methods to eliminate static electricity, master the skills of assembling computers and matters needing attention in assembly, and keep in mind the taboo rules during disassembly.

10. Training Report Training Contents

Use of infusion pump and micropump

1 1. Training Report Training Contents

1, ocean bill of lading process and operation. 2. Air freight flow and operation.

3. Some important documents, such as letter of credit, air bill of lading, consignment note, insurance policy and ocean bill of lading, have been simulated and made.

12. Training Report Training Contents

Training Item 1: (1) What is social etiquette?

1, social etiquette is a moral code of conduct.

The direct purpose of social etiquette is to show respect for others.

3. The fundamental purpose of social etiquette is to maintain the normal social life order.

4. Social etiquette requires that in interpersonal communication and social activities,

(2) Why should we learn social etiquette?

1, learning social etiquette is conducive to improving social psychological endurance.

2. Learning social etiquette can improve humanistic quality.

3. Learning social morality is conducive to strengthening civilized behavior, improving the quality of civilization and promoting the construction of socialist spiritual civilization.

Training project 2:

(A) knowledge of classroom etiquette:

1, class: When the bell rings, students should sit up straight in the classroom. When the class is announced, you should quickly stand up and say hello to the teacher, and then sit down after the teacher answers. You should get to school on time.

2. Listening: Listen to the teacher carefully in class and answer questions in Mandarin.

3. Class dismissed: When the bell rings, all students still need to stand up and say goodbye to the teacher. Students can't leave until the teacher leaves the classroom.

(2) Clothing and instrument etiquette knowledge:

Wearing means wearing underwear, shoes and socks. Its basic requirements are: suitability; Timely; Neat; Generous; Pay attention to the occasion.

(3) Respect teachers' etiquette knowledge:

When students meet their teachers on campus, they should take the initiative to say hello to them. Students should knock at the door when they enter the teacher's office or dormitory. Don't go through the teacher's things casually. Students don't comment on the teacher's looks and clothes, but respect the teacher's habits and personality.

(4) Etiquette knowledge among students:

Students can call each other by their first names, but they can't address each other in impolite terms. When you ask your classmates for something, use polite language.

(5) knowledge of assembly etiquette:

Assemblies are usually held in playgrounds or auditoriums, with solemn manners.

(6) Etiquette in public places on campus:

We should consciously keep the campus clean and tidy, throw garbage on improper occasions and do not damage public property.