Question 1: How to install the gas tank? Yes, the chromatic circle in front of the nut is the sealing ring. The nut rotates counterclockwise to tighten it. After tightening the nut, you can try to see if there is any leakage with soapy water. You should also cultivate the habit of closing the valve every time you use up the gas.

Question 2: The correct installation method of the gas tank and the safe use of gas have always been a topic of concern to people. How to ensure the safety of gas? Let's see Baorun Gas to explain how to install and use gas correctly. 1. A flue must be installed in the flue water heater, and the effective diameter of the flue shall not be less than the diameter of the joint of the exhaust pipe of the water heater, and a baffle shall not be installed in the flue, and an effective wind-proof, rain-proof and snow-proof hood must be installed at the top (end) of the exhaust port.

2. When using the gas water heater, the room must be well ventilated;

3. When using the gas water heater, the exhaust fan must be turned on for forced exhaust. When there is power failure or the exhaust fan fails, the window must be opened for natural ventilation.

4. After using the gas water heater, the valve on the gas pipeline must be closed;

5. Do not use expired gas water heaters. According to the national standard GB17915-1999 "Safety Management Regulations for Household Gas Burning Appliances", the gas water heaters will be scrapped for 8 years from the date of sale.

6. When using the gas water heater, you must read the instruction manual of the product, and use the water heater correctly according to the instructions and instructions on the nameplate.

7. Gas water heaters can only be installed outdoors, on verandahs, in kitchens or non-residential rooms with good ventilation. It is strictly prohibited to install them in bedrooms, basements, bathrooms (except for balanced water heaters), near stairs and safety exits (not restricted beyond 5 meters), where inflammable and explosive materials are stored, rooms with corrosive media, wires and electrical equipment;

question 3: how to install the valve of the gas tank? Turn off the valve of the gas cooker first, and then turn off the main valve of the gas tank! Most of the problems of stove tempering occur on artificial gas (gas) stoves (tempering of liquefied gas and natural gas stoves is rare). Artificial gas cookers do not have pressure reducing valves. Tempering: When the speed of gas leaving the fire hole is less than the combustion speed, the flame will shrink into the fire hole, causing the mixture to burn and heat in the burner, destroying the injection of primary air and forming incomplete combustion. Tempering will destroy the stability of combustion and easily damage the cooker. Tempering is related to primary air coefficient, gas source property, composition, preheating degree of gas-air mixture, fire hole diameter and fire hole outflow speed.

Question 4: How to install the interface of the gas tank:

1. When installing the pressure reducing valve, pay attention to the thread alignment first, and then turn the handwheel counterclockwise in the reverse direction.

2. When rotating, don't use too much force, and the correct hand feel should be relaxed and comfortable, otherwise the threads may not be aligned. At this time, don't screw in forcibly, and re-calibrate it until it is tightened.

3. If it is installed correctly, gently shake the pressure reducing valve body by hand, so as not to move left and right or feel loose; If it is not installed properly, it will shake even if it is tightened.

leak detection method: to ensure the safe use of the pressure reducing valve, brush soapy water at the interface to check whether there is air leakage.

question 5: how to change the gas tank diagram: turn the angle valve of the gas tank clockwise to close the valve, and then turn the nut of the pressure reducing valve clockwise to remove it. You can take the jar and get some air.

can you change cans? Make a phone call or ride a bike to change it back

Then turn the removed pressure reducing valve counterclockwise to the screw button of the tank, and then connect it with the gas tank. Screw it slightly, or it will leak if it is too loose. After tightening, turn the angle valve counterclockwise for one or two turns, and when you hear a hiss, carefully smell whether there is gas smell. If there is, quickly close the angle valve and screw the pressure reducing valve again. If there is no smell of gas, try to fire. Because there is air in the pipeline, you can try it several times until the air is exhausted and the fire catches fire.

question 6: how to install liquefied gas tank and pressure reducing valve? The picture shows that the installation is correct, and the fire on the stove is very strong after the valve of the gas tank is closed, which means that the gas source has not been cut off. Solution: unscrew the pressure reducing valve and check whether the valve of the gas tank leaks. Send it for inspection immediately if there is air leakage.

Question 7: How to install the gas range of the new gas cylinder? Just ask the person who sent the new gas cylinder to help you install it. Please contact the person by phone first.

Question 8: How to install the pressure reducing valve of the gas tank? Yes, the black circle in front of the nut is the sealing ring. Turn the nut counterclockwise to tighten it. After tightening the nut, you can try to see if there is any leakage with soapy water. You should also cultivate the habit of closing the valve every time you run out of gas.