1. When new employees enter the factory, they must receive pre-job training on fire safety, including the basic knowledge of fire safety, the operation and use of fire extinguishers and hydrants, etc.

Second, conduct fire safety training and education for each employee at least once a year, and record the training situation.

Third, the company conducts evacuation drills for all employees every quarter, and provides special training for volunteer firefighters in fire drills, so that each team member can skillfully use fire-fighting equipment.

Four, the company's fire safety director, fire safety administrator, full-time and part-time fire management personnel, fire control room operators and other relevant personnel shall receive special training on fire safety.

Five, electric welding, gas welding, boiler workers and other personnel working in areas with fire hazards and operators of automatic fire control systems must undergo fire protection training and hold relevant certificates.

Six, the workshops, teams and other departments to carry out fire safety education and training should be based on the characteristics of various departments, stages and words.

Seven, the company through various forms to carry out various forms of regular fire safety publicity and education.

Fire inspection and patrol system

First, the enterprise key fire inspection, inspection posts

1, m high pressure synthesis post; Sulfur dissolution hillock; Alkali absorption post;

2.CA condensation post; DPG oxidation station

3. Raw material storage area.

4. Boiler room

Second, the fire prevention and inspection requirements

1, fire patrol, inspected by workshop and department monitor, at least once per shift;

2. During inspection and inspection, the monitor must wear tools and necessary safety protection articles;

3, in the process of inspection in a timely manner to correct violations, properly handle fire hazards, can not be disposed of on the spot, it should be reported immediately. If the initial fire is found, it should be immediately reported to the police and put out in time, and the problems found in the inspection should be repaired in time;

4, fire patrol inspection shall fill in the inspection record, the person in charge of fire safety shall sign the inspection record;

5, fire inspection should include:

(1), there is no violation in using fire and electricity;

(2) Whether the safety exits and evacuation passages are unblocked, and whether the safety evacuation signs and emergency lighting are in good condition;

(3), fire fighting equipment and facilities to maintain normal working condition, fire safety signs in good condition;

(4), remove cigarette butts, heat sources and other debris;

5], other circumstances that need to be checked;

6, fire inspection should include the following contents:

(1) rectification and correction of fire hazards and implementation of preventive measures;

(2) Emergency lighting and exit conditions of safety evacuation passages and evacuation signs;

(3) Fire water source;

(4) The fire-fighting facilities and fire-fighting equipment are working normally, and the fire safety is set according to the signs;

5], key types of personnel and other personnel fire knowledge;

[6], the management of key parts of fire safety;

Once, fire inspection;

Other circumstances that require fire inspection.

Safety evacuation facilities management system

I. General principles

Article 1 This system is formulated in accordance with the Fire Protection Law, Regulations on Fire Safety Management of Organs, Organizations, Enterprises and Institutions, Regulations on Fire Safety Management of Warehouse and Regulations on Fire Safety Management of Crowded Places, and combined with the actual situation of the company.

Article 2 This system is applicable to all production, office and living places (staff quarters, canteens, etc.). ) within the jurisdiction of the company.

Second, the requirements for setting fire safety evacuation facilities

Article 3 Evacuation exits:

1. When the area of the hall or room is not more than 60m2, an evacuation exit can be set; When it is greater than 60m2, there should be no less than two evacuation exits in each hall or room; This item includes: staff canteen, office building and staff dormitory;

2. The distance between the farthest point indoors and the nearest evacuation exit should not be greater than 20m.

Article 4 the evacuation door:

1, the evacuation door should be sliding door, not sliding door, rolling door and revolving door;

2. The evacuation door should be opened outward, and it can be opened inward when the building area is not more than 60m2 and the number of frequent visitors is small. No threshold should be set at the evacuation exit, and no steps and obstacles that affect normal evacuation should be set within 1.4m from the evacuation exit.

Article 5 the evacuation corridor:

1, the evacuation walkway should be evacuated in both directions, the clear width of the walkway should not be less than 1.2m, the ground should be kept straight, and no obstacles affecting personnel evacuation should be set;

2. Fire separation measures should be taken between the evacuation walkway and other parts;

3. The floors, ceilings and partition walls of evacuation walkways shall not be decorated with combustible materials, and it is forbidden to decorate or decorate with materials that produce toxic gases after combustion.

Article 6 the evacuation stairs:

1, the evacuation staircase should be convenient for evacuation, the step layout should be uniform and unobstructed, and there should be no obstacles affecting evacuation in the stairwell;

2. There should be no boiler room and combustible material storage room in the stairwell, and air conditioning ducts, flammable flammable liquid pipelines and flammable gas pipelines should not be laid;

3. The evacuation stairs should be connected to the roof of the Supreme People's Government, and the plane position of each floor should not be changed, and the first floor should be able to go straight to the outside.

Article 7 Safety exits:

1. Offices, staff quarters and other crowded places should have at least two exits on each floor. When the number of floors does not exceed 3 and the number of people does not exceed 50, safety exits or evacuation stairs can be set up. However, auxiliary evacuation facilities must be set up in windows, balconies and other parts.

2. Except in special circumstances, security window should not be installed at windows, balconies and other openings in crowded places. When necessary, devices that can be easily opened from the inside should be installed, and auxiliary evacuation devices should be installed at openings such as windows and balconies.

Article 8 Safety evacuation signs:

1. "Safety exit" should be used as the indicator sign directly above the safety exit and evacuation door;

2. The evacuation indication signs along the evacuation walkway should be set on the wall below the ground height 1m of the evacuation walkway and its corner, and the spacing of light evacuation indication signs should not be greater than 20m, 10m for the bag walkway and 1m for the corner of the walkway. The emergency sign lights set on the ground shall ensure continuous viewing angle, and the spacing shall not be more than 5m;

3. In crowded places such as offices and staff dormitories with inner corridors, evacuation signs or evacuation signs with a spacing of not more than 4m should be set on the ground of their evacuation walkways and main evacuation passages.

4. The evacuation indication markings set on both sides of the evacuation walkway should be continuous, and the evacuation indication signs set on the ground of the evacuation route should be embedded, and the excitation light source or natural lighting amount of the evacuation indication signs should meet the specified requirements.

Article 9 Emergency lighting:

1. If there is no continuous emergency lighting on the "emergency exit" sign directly above the emergency exit and the evacuation door, emergency lighting should be installed in the room with an area of not more than 60m2;

2. Emergency lighting must be installed on each floor of the staircase on the evacuation route;

Third, the management of fire safety evacuation facilities

Article 10 The functional department responsible for the management of the company's fire safety evacuation facilities is the Security Department, and the person in charge of management is the person in charge of his team.

Article 11 The functional department responsible for managing the company's fire safety evacuation facilities is the Security Department, and the person responsible for managing the company's fire safety evacuation facilities is the Security Department.

Twelfth safety evacuation facilities management should meet the following requirements:

1. Ensure that the evacuation passage and safety exit are unblocked, and it is forbidden to occupy or block the evacuation passage and stairwell;

2. When evacuation exits are used in crowded places, the exit doors should not be locked;

4. Evacuation doors that need to control personnel access or have access control system at ordinary times should have reliable measures to ensure smooth evacuation in case of fire;

5, fire emergency lighting, safety evacuation signs, fire safety signs should be intact, clear, should not be blocked;

6. Fences should not be installed on emergency exits and public evacuation walkways. Windows, balconies and other parts should not be equipped with fences that affect escape and fire fighting and rescue, otherwise auxiliary evacuation facilities must be installed in windows, balconies and other parts;

Thirteenth safety evacuation facilities management responsible person shall check every day to ensure that the fire emergency lighting, safety evacuation signs and fire safety signs are intact, clear, effective and smooth. If there is any damage, it should be reported to the management functional department in time to arrange maintenance, replacement and rectification. The person in charge of safety evacuation facilities management is responsible for supervising and accepting the quality of rectification.

Article 14 The Ministry of Security shall organize an inspection of safety evacuation facilities once a month, conduct an experimental inspection of evacuation facilities, and rectify the existing problems in time.

Fifteenth emergency lights are discharged when they leave the factory, and must be charged for 20 hours before use. The performance of emergency lights in use should be checked regularly, and continuous switch test should be carried out every half month or one month to check the circuit conversion and emergency function of the battery, and discharge it to prolong the service life of the battery.

Maintenance and management system of fire control facilities and equipment

A, fire equipment refers to fire extinguishers, fire sand, gas masks and other equipment. Fire control facilities refer to fixed facilities such as automatic fire alarm system, automatic sprinkler system, water curtain system, fire doors, fire shutters, indoor fire hydrants, outdoor fire hydrants, high-level water tanks, water pump adapters and alarm bells in buildings. Fire safety signs refers to the words and patterns related to fire control.

Second, fire-fighting equipment and fire-fighting facilities are prerequisites and fighting weapons for fighting all kinds of fires. All employees are required to take good care of fire-fighting equipment, fire-fighting facilities and safety signs.

Three, non fire cases, no department or individual is allowed to use, try and play with fire equipment, fire facilities and safety signs. It must be approved by the fire department when it is really necessary to use it under special circumstances.

Four, it is strictly prohibited to occupy the fire escape, blocking the exit; It is forbidden to occupy or block fire-fighting equipment and facilities such as fire hydrants and fire extinguishers, and ensure that the exit of the passage is smooth and the fire-fighting equipment is in a ready-to-use state.

5. It is strictly forbidden to misappropriate, dismantle or stop using fire-fighting facilities and equipment without authorization. The acts of destroying fire-fighting facilities, equipment and signs should be dealt with seriously, and those that cause serious consequences should be sent to the public security department for handling, and all employees should be called upon to report the acts of destroying fire-fighting facilities, equipment and signs.

Six, according to the relevant specifications equipped with fire equipment and fire control facilities.

Seven, by full-time personnel to conduct daily inspection of the use of fire-fighting equipment and fire-fighting facilities, according to the performance requirements of fire-fighting equipment and fire-fighting facilities, once a day, once a month or once a year, and timely replacement or maintenance of substandard fire-fighting equipment and fire-fighting facilities.

Eight, the maintenance and management of fire control facilities:

(1) Water quantity and water pressure.

(2) The fire pump is cut off. The fire pump should run once a day. If automatic control is adopted, it is easy to simulate automatic control parameters to start operation, and each operation takes 5 minutes.

(3), alarm valve parts of the working state. Check all water supply main control valves, alarm control valves and accessories every day, and make visual inspection to ensure that the system is in trouble-free state.

(four), the working state of the automatic inflation device (such as pneumatic water tank, pressurized water irrigation).

2, regular inspection

In addition to daily inspection, the system should be inspected regularly once a month.

(1) Pipeline. Check the system piping for corrosion and leakage. If there is sediment in the pipe, wash it.

(2) water source. Check the pool and fire water tank for storing fire water once a month, check the water level and technical measures to prevent the fire water from being used by others, and repair it in time if any fault is found. Check the start-up, water absorption, flow and lift of the fire pump, and use the pressure relief experimental valve next to the alarm control valve to carry out water supply test to verify the water supply capacity of the system.

(3) Check the interface of the water pump adapter and its components once a month to ensure that the interface is in good condition, without leakage and with a cover.

3. Annual inspection

(a), every two years to deal with water storage equipment maintenance, repair and repainting.

(2) The fire pump shall be disassembled and maintained once every two years.

8.3. Periodic inspection of carbon dioxide fire extinguishers

In order to keep the carbon dioxide fire extinguisher in good condition and put it into use quickly and effectively in case of fire, routine inspection, regular inspection and maintenance must be carried out according to the specified use requirements.

1, routine inspection

The company must have specially trained full-time or part-time personnel responsible for the daily inspection of fire extinguishers. Routine inspection is conducted once a week.

(a), check the cleanliness of the fire extinguisher room, whether there is the phenomenon of damp or direct sunlight. Check whether the indoor temperature meets the requirements in winter and summer.

(2) Check whether the pressure gauge pointer on the bottle is in the normal position.

(3) Check the pipeline system for looseness, damage and serious corrosion.

(4), check whether the components such as valves and detection controllers are intact, and whether the switch is set to the normal position.

8.4, indoor fire extinguishing system regular inspection.

Indoor fire hydrant box should always be kept clean and dry to prevent corrosion, collision and other damage. Conduct comprehensive inspection and maintenance at least once every six months. Inspection requirements are as follows

(a), fire hydrant and fire reel water supply gate valve should not have leakage phenomenon.

(2) Fire hoses, hoses, fire reels and all accessories shall be complete and intact, and the reels shall rotate flexibly.

(3), alarm button, indicator light and control circuit function normally and trouble-free.

(4) The appearance of the fire-fighting bolt box and the fire-fighting components assembled in the box are not damaged, the coating does not fall off, and the door glass of the box is intact.

(5) All rotating parts such as fire hydrants, water supply valves and fire reels should be filled with lubricating oil regularly.

8.5, regularly check the fire safety evacuation facilities.

Fire safety evacuation facilities include evacuation passages, emergency exits, evacuation stairs, evacuation instructions, emergency lighting and other facilities. Should be equipped with a corresponding number of fire safety evacuation facilities in accordance with the relevant norms, and file management.

1, daily inspection of safety evacuation facilities, found one of the following problems, should be immediately rectified.

(1), occupying the evacuation passage.

(2), blocking the exit.

(3) Lock the evacuation door.

(4) Stack items on the evacuation stairs.

(five) damage, cover or misappropriate evacuation signs and emergency lighting.

2. Check the performance of evacuation instructions and emergency lighting every month, and replace or repair it in time if any fault is found.

4. Conduct a power switch test once a month to detect the integrity rate of evacuation instructions and emergency lighting, and make adjustments according to the actual situation.

8.6 Regular inspection of fire fighting equipment

Fire extinguishers should be checked every day to ensure that they are always in good condition.

1, visual inspection

(a), check whether the fire extinguisher seal is in good condition. After the fire extinguisher is turned on, even if it is not sprayed much, it must be filled according to the specified requirements. After filling, the sealing test should be carried out, and the lead seal should be firm.

(2) Check whether the pressure gauge pointer is in the green area. If the pointer is in the red area, find out the reason and inflate it after maintenance.

(3), check the integrity of the visible parts of the anticorrosive coating, light fall off should be repaired in time, obvious corrosion should be sent to the fire professional maintenance department for pressure test, qualified before anticorrosion treatment.

(4) Check whether the visible parts of the fire extinguisher are complete; Whether there is deformation, looseness, corrosion (such as compression bar) and damage, and whether the assembly is reasonable.

(5), check whether the nozzle is unobstructed, if there is any jam should be cleared in time.

2, regular inspection

(a), every six months to deal with the weight and pressure of fire extinguishers to conduct a thorough inspection, and should be timely filling.

(2) Check the powder outlet pipe, air inlet pipe, nozzle, nozzle and spray gun of the dry powder fire extinguisher once a year, and check whether the powder outlet pipe is blocked by moisture and the film is broken. Whether the dry powder in the cylinder is caked.

(3), fire extinguishers should be hydrostatic test, generally once every five years. Chemical foam extinguisher should be filled with fire extinguishing agent once a year after two years. Only after passing the pressure test can it be used continuously, and the inspection date shall be marked.

(4) Check whether the environment and location of the fire extinguisher meet the design requirements and whether the protective measures of the fire extinguisher are normal.

Fire hazard rectification system

I. General principles

Article 1 In order to effectively prevent fire accidents and seriously rectify fire hazards, this system is formulated in accordance with the Fire Protection Law, Measures for Judgement, Supervision and Elimination of Major Fire Hazards of the Fire Department of the Ministry of Public Security, Criteria for Judgement of Major Fire Hazards, and Measures for Management of Fire Safety, combined with the actual work of the unit.

Article 2 This system is applicable to all departments in the workshop and foreign construction personnel.

Second, the definition of fire hazards

Article 3 Fire hazards refer to situations that violate (or do not conform to) fire control laws and regulations, have fire hazards and may cause fires, and need to be rectified within a time limit or immediately. The identification conditions are as follows:

1, there are facts that violate or do not conform to fire laws and regulations or fire technical specifications and standards;

2. Due to violation or non-compliance with fire laws and regulations or fire technical specifications and standards, unsafe behavior of people, unsafe state of things, technical defects or management loopholes lead to fire hazards, which may cause fire hazards;

3, need to invest a certain amount of manpower and material resources, within the prescribed time or immediately rectification.

Article 4 Fire hazards that can be rectified in a short time or immediately are general fire hazards.

Article 5 Any person who needs to invest a lot of manpower and material resources and cannot be rectified immediately for a long time, which may lead to the occurrence of fire or the increase of fire hazards, and may cause serious fire accident consequences and social impact, is a major fire hazard.

Third, the main scope of fire hazards

Article 6 Factory building:

1, the address of the factory building is improperly selected, the layout is unreasonable, and the fire prevention spacing is insufficient, which is an illegal building;

2. Open flame workplaces, warehouses and production workshops are staggered;

3. Set up offices and lounges in the warehouses of Class A and B articles;

4, illegal construction, affect the safety layout, occupy the fire spacing, blocking the fire truck passage;

5. The structure, fire resistance grade, number of floors and area of the building are incompatible with the nature of use. For example, the warehouse of Class A and Class B goods adopts buildings with fire resistance rating of Class III or below, which violates or does not meet the relevant fire protection technical specifications;

6. Combustible gas, flammable liquid vapor and air form an explosive mixture, which is likely to cause fire and explosion hazards, and the corresponding ventilation, fire prevention and explosion prevention measures are not taken or improperly set;

7. The number of safety evacuation exits is insufficient, the evacuation width is too small, and the evacuation distance is too far; The safety exits, evacuation stairs and evacuation passages in the building are blocked for standing.

Article 7 In terms of electrical equipment:

1, conductor and laying method are not selected according to the environment, the cross section is not suitable for the load, the wires are randomly connected and pulled, the conductor is seriously damaged, and the contact is poor. , which may cause short circuit, overload, excessive contact resistance and arc and spark;

2. Places where lighting lamps are not suitable for use, inflammable and explosive places do not use explosion-proof lamps, material warehouses use incandescent bulbs with power exceeding 60 watts, or the horizontal distance between bulbs and combustible materials is not less than 0.5 meters. , and adjacent to combustible materials;

3. The material of the switchboard is inconsistent with the use environment, and combustible materials such as wood and bamboo are used, and non-enclosed switchboards are used in places where combustible dust or fibers are generated; The wiring is messy, the line selection does not meet the requirements, and the switchboard is connected with bare wires; The fuse does not meet the rated current requirements or copper or iron wire is used to replace the fuse;

4, the installation and use of electrical equipment can not meet the requirements, selection is not suitable for the use of places, and the lack of safety devices; Choose non-explosion-proof, non-enclosed switches, contactors and motors in places with explosion danger and combustible dust; Connecting too many loads in parallel on the same line or changing high-power electrical equipment into overload without calculation; When changing the cross-sectional area of the conductor and connecting the load, the proper fuse is not installed.

Article 8 Tank farm and finished product storage area:

65438+

2. Flammable liquids are mixed with flammable, combustible solids and combustible gases, and oxygen cylinders, acetylene cylinders, substances that burn in water are put together with substances containing water, and the transportation and packaging methods do not meet the fire prevention requirements;

3. Repair the used oily cotton yarn, oily gloves and other oily fiber items and flammable packaging. Don't store them separately in a safe place and dispose of them regularly.

Article 9 Fire safety protection:

1, the evacuation indication sign is missing, damaged or marked incorrectly, which affects the safe evacuation of personnel;

2, storage tank area, hoist, welding machine and other equipment without electrostatic grounding device or power frequency grounding resistance of grounding device is greater than 30 ohms; Important equipment and buildings such as storage tank area and reaction kettle are not equipped with lightning protection facilities or the lightning protection facilities are in disrepair for a long time, which can not effectively discharge lightning;

3. The installation of electrical products or the laying of lines and pipelines does not conform to the safety technical regulations, which endangers fire control safety.

Article 10 In terms of open flame operation:

1, fire source or heat source (high temperature steam, electrical appliances, etc. ), close to combustible objects and substances;

2. Store flammable and combustible substances in the workplace with open flames, and do not dismantle or take safety protection measures for open flames;

3. In violation of the ban, smoking and using naked flames in places with fire and explosion hazards;

Eleventh fire equipment and facilities:

1, the fire water source and fire hydrant are not installed or improperly set, and the water pressure is too small and damaged, which is not suitable for fire extinguishing;

2, lack of fire fighting equipment, equipped with quantity and performance does not adapt to the place of use, improper placement or damage;

3, outdoor fire control facilities are buried, occupied, damaged, affecting the use of.

Twelfth fire control organization and management:

1, failing to establish fire safety rules and regulations or operating procedures as required, or failing to implement them;

2, key parts of the fire facilities management personnel on duty or fire inspectors off-duty; Personnel in key jobs and special positions have not received fire protection training;

3. Illegal closing of fire control facilities, violation of safety operation rules, unscientific and reckless risk, random removal or replacement of safety devices of inflammable and explosive articles or places, and violation of fire control safety regulations.

The fourth is the rectification of fire hazards.

Thirteenth of the following acts in violation of fire safety regulations, the responsible unit shall instruct the relevant personnel to correct on the spot and supervise the implementation:

1, illegally entering the place where inflammable and explosive dangerous goods are produced and stored;

2, illegal use of open flame operation or smoking in places with fire and explosion danger, the use of open flame and other violations of the ban;

3. Lock or block the exit, or occupy or pile up items that affect the smooth evacuation passage;

4, fire hydrant, fire equipment is blocked can't be used or used for other purposes;

5, fire facilities management personnel, personnel on duty and fire patrol personnel off work;

6, illegally shut down the fire control facilities, cut off the fire power supply;

7. Other behaviors that can be corrected on the spot.

Article 14 Handling of fire hazards that cannot be rectified on the spot:

1. The workshop or department with fire hazards shall report the existing fire hazards to the fire safety manager or the person in charge of fire safety in the company's security department in time according to the principle of being responsible step by step, and put forward the rectification plan.

2. If the workshop or department can rectify itself, the Ministry of Security shall determine the rectification measures, time limit, departments and personnel responsible for rectification, and implement the rectification funds.

3. It takes a certain time and process to rectify fire hazards. Before the fire hazard is eliminated, the responsible workshop shall formulate transitional preventive measures and implement them to ensure safety. If safety cannot be guaranteed, which may cause fire or endanger personal safety at any time, the responsible workshop shall take measures to stop production and rectify the dangerous parts by itself.

4. If the workshop cannot be rectified, the workshop should report the existing fire hazards and rectification scheme to the company's security department.

Article 15 For the fire hazards discovered and notified by the company's superiors, after the responsible workshop completes the rectification according to the above provisions, it shall fill in the "Fire Hazard and its Rectification Record" and report it to the company's security department.

Safety management system for electricity and fire use

I. General principles

Article 1 This system is formulated in accordance with the Fire Protection Law, Regulations on Fire Safety Management of Organs, Organizations, Enterprises and Institutions, Regulations on Fire Safety Management of Crowded Places, Regulations on Fire Safety Management of Warehouses, Regulations on Electrical Safety Management, Measures for Fire Safety Management, and Regulations on Safety Technology Management of Loading and Unloading Operations.

Article 2 The management of fire and electricity used in this system refers to the management of fire and electricity used by employees and constructors of this unit in the raw material storage tank area, finished product storage area and other jurisdictions due to work needs or at work.

Second, the fire safety management

Article 3 The hot work and fire operation such as electric and gas cutting welding in raw material storage tank area and finished product storage area shall be examined and approved by the company's safety fire department and the person in charge of workshop fire management in raw material storage tank area, and other workplaces shall be examined and approved by the company's safety fire management department.

Article 4 Open flame is strictly prohibited in the warehouse of inflammable and explosive dangerous goods in the raw material tank farm. When using naked fire outside the inflammable and explosive dangerous goods warehouse and in the goods storage area, a hot work permit must be obtained and approved by the person in charge of fire safety in the storage area or storage area. The hot work permit shall indicate the hot work place, time, hot work person, on-site guardian, approver and fire prevention measures.

Article 5 Examination and approval of hot work: The hot work department or personnel shall apply to the fire management department in the operation area, and the person in charge of fire safety in the operation area shall approve the application for a hot work permit, remove flammable and combustible substances, equip with fire-fighting equipment, implement the on-site guardian and safety measures, and confirm that there is no danger of fire and explosion before welding operation can be carried out at the specified time and place. If cutting and welding are carried out at the place where cutting and welding metal parts are in direct contact with combustible substances, such as vehicles carrying goods, someone should be guarded for a period of time after cutting and welding, and it is confirmed that there is no danger before leaving.

Article 6 When the local construction of a building shared by two or more workshops requires the use of open flames, the construction department shall notify the user department to take preventive measures, separate the construction area from the use area with fire prevention measures, remove the flammable and combustible substances in the hot work area, equip with fire-fighting equipment, and designate a special person for supervision to ensure the fire safety of the construction and use scope.

Seventh crowded places shall not use open flame lighting or heating. Special circumstances require special care. Fire prevention and heat insulation measures should be taken between fire, flue and other heating facilities and combustible materials.

Article 8 The person in charge of fire control safety shall, when examining and approving the place where the stove is used, conduct examination and approval according to the classification of stored goods and the provisions on fire prevention distance, and formulate a fire prevention safety management system, which shall be implemented by people.

Tenth dangerous goods loading and unloading operations, should strictly implement the "dangerous goods transport rules" in the relevant provisions of fire safety. Explosion-proof forklift trucks should be used for loading, unloading and handling dangerous goods, and fire extinguishers with good performance should be equipped on board. Other loading and unloading tools should also take fire prevention measures.