main features of starry ceiling

1. Strong decoration:

The artistic effects of colors are diverse, dynamic, textured and spatial. At the same time, the optical fiber is flexible and can freely guide the light to the required position according to different ideas. Very personalized charm.

2. high safety:

photoelectric separation is realized, and the optical fiber part does not have any electric energy and heat energy, so it can ensure safety in any case by contacting the luminous optical fiber.

3. Health and environmental protection:

The light emitted by fiber-optic lighting filters the cold light of infrared rays and ultraviolet rays, and the light color is soft and pure, which does not generate heat, thus reducing the environmental burden on the air conditioning system, protecting vision health and realizing high efficiency and energy saving. The optical fiber material itself is also environmentally friendly and does not contain any form of volatile substances.

4. Long service life, easy operation and maintenance:

The service life of the optical fiber itself is more than 21 years, and it can be used indefinitely once installed. Switch operation and maintenance are simple and convenient. In case of moving, it can also be reused in the new house after demolition.

Installation steps and precautions of starry sky ceiling

1. Selection of ceiling materials for optical fiber starry sky

Polyester fiber sound-absorbing board is usually used as ceiling materials in theater decoration, and its advantages are as follows:

① It is convenient to wear optical fiber;

② The construction is convenient, the corner treatment is simple, and it can be seamlessly spliced, freely cut and chamfered, and different shapes can be spliced;

③ Good sound absorption performance;

④ Various colors can be selected, and post-processing is not needed;

⑤ environmental protection and non-toxic.

2. Optical fiber size and quantity configuration

According to the length-width ratio of the installation room, a considerable number of optical fibers are configured, and the number of optical fibers with different lengths and diameters is reasonably distributed. Too dense or too sparse will lead to unsatisfactory final results.

when threading optical fiber, thread the shorter optical fiber near the light source machine and the longer optical fiber far away from the light source machine. For example, the 1-meter optical fiber passes through the position close to the light source machine, and then the 1.5-meter optical fiber and the 2-meter optical fiber have the same length in turn. Optical fibers with different diameters are distributed among them, and super bright stars, bright stars and micro bright stars present a realistic starry night sky. Starlight flickering, you can make different colors appear alternately, and you can also locate a certain color.

3. Install optical fiber

This determines the final effect. On the home page, mark the position that needs to be drilled on the polyester fiber sound-absorbing board, and the star arrangement position can be DIY into your favorite constellation. Then drill holes in the marked places according to the opening size corresponding to the optical fiber, and then penetrate the optical fiber into the polyester fiber sound-absorbing board.

centering on the position where the machine is placed, put the optical fiber down from the top surface of the ceiling, pass through and leave a section, and drop a drop of epoxy resin adhesive at the joint between the optical fiber and the sound-absorbing board to fix it. The resin adhesive should be slowly dried for more than 2 hours.

4. Installation of light source device

The light source device must be installed in a ventilated, dry and convenient location on the ceiling. If the ceiling is fully enclosed, a movable access port should be set at the position where the light source device is placed, which is convenient for the placement and maintenance of the light source device.

5. Specific installation steps

① A 221V power cord shall be reserved on the top surface, and an oblique three-eye 11A socket panel shall be prepared. The corresponding wall switch is reserved for the wall surface.

(2) In advance, lay a keel (wooden keel or light steel keel) with a height of more than 8CM on the top surface.

(3) After the keel is finished, the ceiling materials (such as gypsum board) that need to be installed with optical fiber can't be put on first, and the putty should be put on the ground first. After the optical fiber enters the site for installation, the flat-fell seam of gypsum board should be reserved with a width of about 5CM, so don't batch it, and then fill it after the gypsum board is installed on the ceiling.

④ The optical fiber starry sky is installed on the gypsum board on the ground by the optical fiber starry sky top installer. After the ground installation is completed, the corresponding gypsum board is installed and fixed to the ceiling keel by carpenters.

(5) After the ceiling is installed, the painter will fill all the joints of the gypsum board, and paint spraying or paint can be used as needed. After the paint or paint is dry, the excess optical fiber will be cut flat, which is more effective.

⑥ The light source generation and control system must be installed on the suspended ceiling in a ventilated and dry place for easy maintenance. If the suspended ceiling is fully enclosed, an inspection hole should be opened at a suitable position of the suspended ceiling to facilitate the placement and maintenance of the control device.

6. Tips:

① The module is powered on and installed in the whole process of connection, so as to check whether the fiber-optic lamp on the module emits light normally;

② the power cord is reserved inside the edge top, so as not to affect the overall beauty.

③ The included angle should be 91 degrees when erecting the keel, because the module is a standard right angle, so in order to avoid irregular fitting, the preliminary work should be done well.