Aluminum button board ceiling installation method.
1, according to the design elevation of the aluminum button plate ceiling in the surrounding wall bouncing line, the bouncing line should be clear, accurate location, the level of the allowable deviation ± 5mm.
2, along the elevation line fixed angle aluminum, the role of the angle aluminum is the edge of the ceiling parts of the seal, the corner of the aluminum commonly used specifications for the 25 * 25mm, the color and luster should be the same as the aluminum alloy panels, the corner of the aluminum is more than with the cement nails fixed to the wall columns.
3, determine the keel position line, because each aluminum alloy block plate is formed panel, generally can not be cut into pieces, in order to ensure the integrity of the ceiling finish and installation reliability, need to be based on the size of the aluminum alloy specifications, as well as the area size of the aluminum button plate ceiling to arrange the structural dimensions of the ceiling skeleton. The basic arrangement of the aluminum alloy square plate finish is: plate combination should be complete, four perimeter stay edge, stay edge around the symmetrical and uniform, will be arranged to arrange the position of the skeleton frame line drawn on the upper side of the elevation line.
4, in the installation of aluminum ceiling, pay attention to the main keel hanging point spacing, according to the design of the recommended series selection, the middle part of the arch should be, keel arch height is not less than 1/200 of the span of the room surface. the main keel should be installed in a timely manner after the correction of position and height. To control the leveling of the keel frame, first of all, the vertical and horizontal elevation control line should be pulled out, starting from one end, while installing and adjusting the suspension height of the boom. To be a large surface leveling, and then some of the single keel with bending and warping adjustments, until the leveling meets the requirements.
5, according to the specifications of the aluminum buckle plate size, installation and board supporting the secondary keel, secondary keel through the hanging pieces hanging on the main keel. When the length of the secondary keel needs to be more than one continuation of the long, with the secondary keel connector, in hanging the secondary keel at the same time, will be connected to the relative end, and first straighten after fixing.
6, comprehensive correction of the location and level of the main and secondary keel. Connectors should be staggered installation, check the installed aluminum ceiling skeleton, should be firm and reliable, in line with the relevant norms before the next step in the construction.
7, the installation of aluminum buckle plate, should be the second bone straight. Buckle plate should be flat, not warped, ceiling plane flatness error shall not exceed 5mm.
8, aluminum buckle plate installation should be completed in a timely manner to clean up.
How to remove the ceiling in the bathroom
The general ceiling will have a zero, that is, the last installed on the piece, as long as you find the piece of zero can be removed. The last piece of plastic buckle plate is directly on the top of the card, as long as the force to the wall in the direction of the move on the line, while moving vigorously, while the hand beat the buckle plate, the piece is removed, the other is fixed with screws, the screws one by one unloading can be, the long strip of aluminum buckles dismantling method is also the same. The dismantling method of the integrated ceiling is basically the same as the above method, and it should be said that it is easier to dismantle than the above two ceilings.
How to dismantle the square aluminum ceiling in the bathroom?
Partially support the first floor.
However, in the final finishing stage of the ceiling, the boards are usually cut because of the length. At this point, the gap between the cut boards and the edge strips may be larger, and it will be necessary to hit the glass glue to prevent the buckling board from buckling.
But I do not understand, since the master is good, and in the neighborhood of the words, why not ask him to help directly? Maybe the problem is very simple, if you do not know how to mess it up, if you really want to remove the keel, not to call the installer?
And now the most important thing is to figure out whether the floor leakage or water pipe leakage. So you can first use the suction cup to open the closest to the downpipe, buckle in the triangle keel on the buckle plate, to determine the situation.
Floor leakage waterproofing, water hack leakage to be repaired, and it is best to notify the property together to solve the problem
How to install the bathroom ceiling grommets
The bathroom integrated ceiling installation steps are as follows:
1, a clear location
Design drawings and site conditions relative to the clear electrical appliances and keel with *** place. Determine the height of the ceiling installation, the bath bar is generally 2.1m-2.3m between the maximum effect can be played.
2, to ensure that the level
After the height is clear, do the horizontal installation angle line. With screws or glue (in case the tiles are damaged) to fix the corner line, the corner of its diagonal should be collated neatly, leaving no obvious gaps.
3, punching and positioning
After the keel position is determined, use an impact drill to punch holes. Gall specific length cutting, assembly boom screws. Boom screws fastened in the drilled holes. This link can be carried out at the same time as the previous step.
4, install the keel
The main keel will be installed in the boom screws under the fixed ring, triangular keel fixed to the main keel. Properly adjusted after installation, gradually tighten the screws at the joints to ensure straightness.
5, the ceiling on the shelf
Square aluminum ceiling has two installation methods: edge mounted, middle mounted, depending on the specific circumstances. It is very important to install the first board, which determines
the position and level of other boards. Bathroom ceiling can be based on different shapes, choose a variety of materials, such as flat roof can be used PVC buckle plate, aluminum buckle plate, plastic aluminum plate, with light steel keel. The dome type and other artistic ceiling can choose a soft
point of waterproof board, soft board, plastic aluminum board, or then decorated with a variety of colored glass decoration.
From the general height of the ceiling, most of the developed countries, the family bathroom is shorter, and many domestic homes, bathroom height equal to its
other rooms, so in order to avoid empty, cold silence, the general height of the ceiling can be designed in the 2.2 meters W64;2.4 meters between. In the area of more than 8 square meters, may wish to install cosmetic cabinets above the washbasin, away from the water source
Hanging storage boxes, or set aside a place to do the daily change of clothes.
In the installation, to ensure that the keel installation level, generally speaking, the spacing deviation should be controlled within 1.5 cm. If there is a deviation in size, it should be adjusted and then inserted in order, not hard insertion, in order to prevent deformation. Bathroom ceiling materials should be used metal, plastic and other materials, because the bathroom is a place to bathe and wash, moisture will be very large, with wooden materials are easy to deformation, which has nothing to do with the waterproofing is good or bad.
How to install the bathroom ceiling?
The keel choose light steel keel, because the wooden keel will be deformed or corroded for a long time.
When installing the boom and playing expansion screws is different from other places, you can't play too deep, because it may damage the waterproofing of the people upstairs, resulting in their own home was soaked.
Compared to the living room and other places of the ceiling bathroom ceiling mainly rely on the side of the keel, so the side of the keel with glue must be firm.
Some novice decorators (most) will not install the bathtub exhaust fan, only to hang or use something to press on, very unsafe, so the installation of wow time to keep an eye on.
How to install pvc grommet ceiling
Use a tape measure to measure the length and width of your bathroom, go to the building materials market to find a PVC is also plastic steel business, choose your favorite style or color, the length and width of your bathroom to tell the store owner, he will give you arrangements!
Generally speaking, PVC board has a square meter of 25-80 yuan ranging! For example, 30 yuan a square meter of the board, the bathroom area is 5 square meters, 240 yuan is not bad to do a good job! PVC ceiling is both beautiful and generous, easy to dismantle!
How to install the bathroom integrated ceiling
In the past, the bathroom ceiling treatment and its simple, generally do not do special treatment, is to install a light bulb for lighting even if. But with the development of the times, the requirements and design of the bathroom ceiling is more and more innovative, beautiful, available materials and installation methods are also diverse, its lighting is not its only function. Now most people will install an integrated ceiling for the bathroom, so how to install the integrated ceiling? Here to share the skills of integrated ceiling installation.
First, prepare the raw materials for the ceiling
In order to facilitate the installation of new electrical modules, the choice of aluminum ceiling, the size of the general choice of 300mm × 300mm, 600mm × 600mm two.
Second, the installation of the ceiling
First of all, in preparation for the installation of the ceiling of the place to pull a good level line, hang a good light steel keel;
will be a special triangular card code buckle into the triangular keel, according to the specifications of the installation of the square plate on the intergraphic card (triangular keel only need to be used in one way, horizontal not used);
will be installed after the keel, directly into the triangle will be pressed into the roof of the aluminum ceiling bone seam can be. Installation of aluminum buckle plate, pay attention to the direction of the buckle plate folded edge with a small pit to be inserted into the triangular bone seam, not with the direction of the pit folded edge, a little pressure, you can achieve a compact and seamless effect.
Third, select the electrical module
According to the needs of different functional areas of the bathroom space and their own preferences, arbitrary selection of electrical modules, select these electrical modules, can be in the decorative materials market or Gome, Suning and other home appliances stores. Above the bathing area can choose to install heating modules, toilet above the gas module, bathroom central lighting module, washbasin and vanity mirror above the spotlight module, pay attention to the mood can also choose to install MP3 audio module.
How to install bathroom ceiling lights illustrated
bathroom ceiling light installation: installation of large lamps and lanterns, exhaust fans and other things should be done separately to fix the keel, should not be directly resting on the aluminum buckle plate, otherwise it is easy to make the aluminum buckle plate fall off, there is a certain safety hazard, but also affects the aesthetic. At the same time to reserve the location of the bath fan and other things, but also to reserve the check port. In home decoration, the general public do not like to set up access holes to the ceiling, think that affects the aesthetic, and once the ceiling pipeline equipment failure, it is impossible to check what parts, what causes the failure, and even more can not be repaired. Therefore, for the laying of pipeline ceiling, or set up access holes for good, can be set in a more hidden easy to check the parts, and access holes for artistic treatment. So that some parts that are prone to defects will be handled properly. In the whole installation process should be strictly in accordance with the above methods to avoid omissions caused by regret.
The ceiling of the kitchen bathroom how to install ceiling lights
You buy the lights to the ceiling installation master on the line, just outsourcing the lights may have to pay the store labor. If you buy the ceiling where to buy the lights, then you do not have to think about this problem
Kitchen and bathroom ceiling in the process of renovation in which step to carry out
This depends on the situation.
If the requirements are high in the upper cabinets are installed, you can ensure that the upper seal is good. It also saves material
No, it's a carpenter's thing. Very simple operation.
Generally speaking, the keel is fixed on the cabinet.
But installing cabinets to make holes in the wall, latex wall as long as you do not use water to wipe, dust with a chicken feather duster on the clean