Brief introduction of electrostatic fume purifier;
First of all, Bian Xiao briefly introduces what is an electrostatic fume purifier. Electrostatic fume purifier is a kind of large range hood, but it is larger than domestic range hood and has more obvious fume absorption effect, so it is widely used in large factories and hotels.
Second, the working principle of electrostatic fume purifier:
Secondly, Bian Xiao introduced the working principle of electrostatic fume purifier. The working principle of electrostatic fume purifier is the same as that of ordinary range hood. It uses the strong centrifugal force to make the oil fume get involved in the airflow, and uses the current in the body to decompose the oil fume. Generally speaking, the products of decomposition are carbon dioxide and water vapor, but there will also be a small amount of lampblack discharged into the air. Compared with the range hood, the purification and environmental protection effect has been greatly improved. Moreover, there is a baffle at the outlet of the electrostatic oil fume purifier, and an oil collecting tray is arranged below the baffle. When the oil and gas are sprayed on the baffle, the oil and gas will automatically fall down under the action of gravity, so it can be used for a long time, just cleaning the oil collecting tray.
Three, the installation method of electrostatic fume purifier:
1. Installation conditions
Electrostatic fume purifier must have good installation conditions. It is necessary to ensure that the installation site can bear the weight of the electrostatic fume purifier instrument, and at the same time, it can leave space to facilitate the opening and closing of the equipment door, which can facilitate the future maintenance and maintenance work. In the process of construction, it is necessary to ensure that no sundries will fall from the installation site, so as to ensure the safety of installers. In order to make the electrostatic fume purifier work normally, the installation site must be able to provide a rated voltage source of 220 -240 volts and a rated power of 50 -60 Hz.
2. Installation process
Install the electrostatic fume purifier on a fixed ground or machine body, and then adjust the horizontal angle after fixing the equipment. Make sure that the range hood is placed horizontally. Generally speaking, the air outlet and air inlet of the range hood are left in and right out. After the equipment is installed and fixed, install the flanges and install the flanges at both ends respectively. After the method is fixed, carefully check the sealing condition of the joint. The last step is to connect the wires, and it's ok to connect the wires.
Fourth, the cleaning of electrostatic fume purifier
1. Dismantling the cleaning parts: firstly, after cutting off the power supply of the oil fume purifier, remove the oil fume purifier from the hoisting position, then disassemble the oil fume purifier and take it out in turn: the lighting bulb, the oil collecting box, the bottom plate, the sealing ring and the impeller, and finally put out the inner core of the machine body.
Second, soak and clean the parts: find a bigger container, then pour the cleaning solution and put the removed parts in for soaking. The amount of cleaning liquid should not be too little or too much, and it should be based on the cleaning parts that can be wetted and removed. Large pieces should be cleaned with a rag dipped in cleaning solution. The soaking time of cleaning parts depends on the degree of oil pollution, generally 15-20 minutes is appropriate.
Third, brush dirty parts: soaked dirty parts are easier to clean, and can be washed repeatedly with an iron brush and a brush dipped in cleaning solution. The oil fume purifier with serious oil pollution can only be cleaned by taking special cleaning measures. The usual method is: first, grab the thick oil stains with flat-headed tools, then soak them, then scrub the serious oil stains with caustic soda water, and wear rubber gloves when scrubbing to prevent caustic soda.
Maintenance technology of lampblack purifier: Maintenance of electrostatic lampblack purifier: Under normal operation, the electrostatic lampblack purifier is cleaned once every 1~2 months to ensure the effect of lampblack purifier. After Xuchang oil fume purifier was used for a period of time, the thick oil accumulated on the electrode plate affected the discharge of the electrode plate, thus reducing the pollution effect.
This paper introduces the working principle and installation steps of electrostatic fume purifier. Through the introduction of Bian Xiao above, I think everyone should master the installation method of electrostatic fume purifier! The above is the related content of electrostatic fume purifier, I hope it will help everyone!
Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~