Current location - Recipe Complete Network - Food world - Beaded mini animal pendant tutorial
Beaded mini animal pendant tutorial
The tutorial of beaded mini animal pendant is as follows: (lovely rabbit beaded pendant).

The basic knots used in beaded cute rabbit pendants are snake knot, oblique knot, reverse knot and sparrow head knot; In order to distinguish lines, the two lines to be used are called contour lines (dark purple and gray lines) and fill lines (light purple and pink lines).

1, an 80cm contour line is folded in half.

2. Leave a length of 7 or 8 cm on it and weave two snake knots.

3. Add two contour lines to make a line and make a horizontal axis. Two vertical lines are woven into two oblique knots respectively.

4, the axis is the same, add two threads to the left and right, leave the length of 10cm above, and make a diagonal knot each.

5, the axis is the same, add a color filling line on the left and right to weave, the upper and lower lengths are equal, and each weaving is a diagonal knot.

6. The axis is unchanged, and the left and right sides are turned around with the colored lines at the bottom, and the diagonal knots are woven upwards.

7. The axes are the same. The two colored lines are folded in half and placed on the left and right sides respectively. The colored lines pass down and tighten after the lines turn to the top (this is called hanging lines).

8. There are four contour lines in the middle, and the long two lines are used as weaving lines to weave the bird's head knots left and right, and weave about 6 or 7 bird's head knots respectively, so it is appropriate to barely wrap the beads but not completely.

9. pass through the beads.

10, with two lines in the middle and diagonal lines on the left and right sides.

165438+ or reverse it to the back and weave a diagonal knot.

12. Now knit a small bow around your neck. Look to the left first. There are four lines in the lower left corner. The second line from the left is the sideline and the third line is the axis. Tie a diagonal knot down and use the same method in the lower right corner.

13. The two lines woven in the previous step are now used as axes, and a colored filling line is hung separately.

14, tie two oblique knots with two central lines as axes respectively.

15, with the same axis, rotate in one direction and weave a diagonal knot respectively.

16. The knitting in the previous step is an axis, the colored thread is a braid, and each braid consists of two oblique knots.

17, the left and right second lines are used as axes respectively, and the gray line wrapped with colored lines is used as knitting line, and a diagonal knot is knitted upwards.

18, the axis is unchanged, the first thread on the left and right sides is woven, and a diagonal knot is woven downward.

19. Take the weaving in the previous step as the axis and the colored thread as the weaving, and weave a diagonal knot.

20, axis unchanged, respectively, hang a color line.

2 1, the axis is unchanged, and the diagonal winding is woven with colored thread.

22. The shaft of the previous step is braided and a diagonal knot is braided. Here, the rabbit's lower body is woven. If you feel that too much will affect the next move, you can cut off the extra thread and burn it with a lighter to prevent it from loosening.

23. Start knitting rabbit ears from different directions, add an outline on the left and right sides respectively, leave a length of 5 cm on it, then knit and tie a diagonal knot with the first line on the left and right sides as the axis.

24. Take the contour line as the axis and weave three oblique knots with colored lines.

25. The innermost thread is tied in a diagonal knot.

26. Repeat the above steps in the opposite direction for five times; The sixth time, the filling line in the middle was picked out without weaving, and only two rose-red oblique knots were woven in the middle.

27. Cut off the three colored lines in the middle.

28. As shown in the figure, weave the contour line on the right side into two oblique knots with the overlapping of the curved contour line and the filling line as the axis.

29. Tighten the threads separately, make adjustments, then cut off the redundant threads and burn the threads with a lighter.