Bean sprout machine is a machine that makes bean sprouts by using water circulation watering. Usage:

1. (Sowing): Spread the right amount of seeds evenly on the net, and then cover the other net on it, and increase the pressure appropriately, which can make the seeds absorb water evenly.

2, (watering): replace the bottom water twice a day.

3, (light): 2 days before germination should be in a shady place, especially soybean and mung bean, has been in the shade out of cultivation, other vegetable seeds germination, give appropriate light, help the growth of plants.

4, (Harvest): Most of the seeds are ready to eat in 3-5 days.

6. (Storage): Keep the remaining vegetable sprouts and seeds in the freezer of the refrigerator for 7 days for consumption.

2. Bean sprout machine temperature control methods:

Control the temperature inside the box, usually installed in the inner wall of the box heat sensor, such as contact thermometer, resistance thermometer, etc., used as a transformer for temperature measurement and adjustment devices, but also as a control of heat sources (such as electric heaters) on and off the electric signal switch. That is, the internal temperature of the box to cultivate bean sprouts required for the best temperature (27 degrees), the heat sensor can automatically send a signal to cut off the power line and stop heating. On the contrary, when the internal temperature of the box is lower than 27 degrees, the heat sensor can automatically send a signal to connect the electric line and heating in time.

Since the bean sprout machine in the cultivation of bean sprouts can automatically control the temperature, so that the growth of bean sprouts in the appropriate conditions of constant temperature, to overcome some of the disadvantages of the manual operation of the temperature change uncertainty, which promotes the growth of bean sprouts, shorten the cultivation time.

The automatic temperature control and adjustment range of the bean sprout machine, generally between 18-35 degrees, but the actual use of more than the choice of about 27 degrees.

3. Bean sprout machine production process:

First, the soft plastic pipe or hose will be under the water tray out of the pipe for drainage. Sprouting box on top of a 10-centimeter-thick object, and then put the water spray box on top of the soft plastic pipe or hose to connect the water tank with the nozzle conduit.

The controller "power plug" connected to 220 volts, 50 Hertz AC, the germination box and then connected to the "control power" plug and controller "temperature control power output" socket, and then the controller "temperature control power output" socket. Socket, and then the controller temperature control knob set at the desired temperature, bean sprout machine can begin to work. It is very simple and easy to use.

In order to ensure the correctness of the temperature control accuracy, when the machine is installed, or after a period of time after the use of the following method of proofreading the accuracy of the temperature control: the temperature sensor probe and the standard thermometer next to each other, placed in the upper layer of the germination box. After the germination box is controlled and heated, start to calibrate the value of the twist indicator on the thermostat, which refers to the accurate control temperature value at 1, 2, 3, 4, 5, etc. However, the twist indicator at "1, 2, 3, 4, 5, etc." can be used to check the accuracy of temperature control. However, after the twist is pointed at "1", control the heating in the germination box and observe the indicator light. Start heating, "heating indicator" is bright, "constant temperature indicator" is not bright. After heating for a period of time, when the "heating indicator" extinguished, and "thermostatic indicator" bright, that is, the temperature in the germination box to reach the value of the control temperature, which is to read out the value of the standard thermometer, that is, is the rotary screw refers to in the "1 "at the control of the constant temperature value, record and continue down the proofreading, until the actual control temperature value of 1-5 gears all the proofreading is complete.

Put the seed beans into the germination box according to the routine soak on the water tray (water tray to try to maintain the level of placement), and then insert the temperature sensor probe into the top of the germination box on the probe frame, will control the temperature knob pointed at 25-27 degrees. Then the bean seeds began to sprout, at this time you can adjust the automatic spraying interval to 2-3 hours spraying once, to the buds grow 1 cm, adjusted to 4-6 hours with a shower. Adjusted water temperature should be 3-5 degrees higher than the specified temperature, so that the temperature of the spray water and the temperature of the bean sprouts at that time is basically the same as appropriate.