First, soybean milk machine failure phenomenon: beans can not be broken.
When many users use it, they often find that the soybean milk from the soybean milk machine tastes bad and is very rough. At this time, many people will attribute this phenomenon to the quality problem of soybean milk machine. As we all know, this is a phenomenon caused by a glitch in the soymilk machine. In this case, it is generally considered that there is a problem with the filter screen of the soymilk machine.
Solution:
If the mesh of the side net or bottom net of the net cover is blocked, the soybean milk produced by the soybean milk machine will be coarse and have larger particles. It is necessary to disassemble the soymilk machine, soak the net cover in boiling water, add detergent, soak for about 15 minutes, and brush it clean with a cleaning brush. This failure was caused by the fact that Dachuan users didn't clean the soymilk machine when they usually used it.
For some net-less soymilk machines, the failure of blocking the net cover will not occur. At this time, the main consideration is whether the voltage of the soymilk machine is too low or too many beans are put in, which exceeds the capacity of the soymilk machine. This situation is caused by improper user operation, and only by changing the operation method can it be solved.
Second, the failure phenomenon of soybean milk machine: combustion failure
Solution:
The soymilk machine is burnt. It is generally believed that there is something wrong with the soymilk machine and it cannot be used any more. In fact, the soymilk machine burned out. It may be that the heating pipe of the soymilk machine was cleaned, so it is necessary to clean the heating pipe of the soymilk machine.
In addition, using mung beans to make soybean milk alone may also cause such a failure. At this time, it is best to add peanuts or soybeans to do it together, which can solve this problem.
Third, the failure phenomenon of soybean milk machine: overflow failure
Solution:
In the process of making soybean milk, the benefits of soybean milk are everywhere. This kind of situation is more common, and I believe many people have encountered it. In fact, this mainly comes down to the following reasons:
1. The mesh of the net cover is blocked. Treatment method: clean the filter screen.
2. The spill-proof electrode was not cleaned. Treatment method: clean the spill-proof electrode.
3, too much water, treatment: please add water between the upper and lower water lines.
Fourth, the failure phenomenon of soybean milk machine: lack of fire, early alarm failure.
Solution:
Obviously, the soybean milk was not cooked well, but the soymilk machine called the police in advance. This failure is not only caused by the soymilk machine itself, but also caused by incorrect operation.
For example, if beans are soaked in water for too long and deteriorate, the safety identification function of the soymilk machine itself will issue a safety alarm function to remind users. Or because too much water is added, which exceeds the load of the soymilk machine, so that the soymilk machine cannot work. Therefore, when using the soymilk machine, it is best to add water between the upper and lower water lines, so that the soymilk machine can operate normally.
Extended data:
Fault 1: Heavy vibration and noise.
Cause analysis:
1, put too many beans or too little water;
2. The mesh of soybean milk is blocked;
3, motor bearing wear;
4, motor carbon brush wear;
5, motor or other parts screw loose.
Solution:
1, the amount of beans and water to be put in should meet the requirements;
2. Thoroughly clean the mesh of the soybean milk net;
3. Replace the motor or motor bearing;
4, adjust or replace the motor carbon brush;
5. Tighten the screws.
Problem 2: beans can't be broken.
Cause analysis:
1, put too many beans;
2, blade wear;
3, the computer board is affected with damp, and the chip program is chaotic;
Solution:
1, add a proper amount of beans as required;
2. Replace the new blade;
3. Replace the computer motherboard
Fault 3: alarm after plugging in, and the indicator light flashes.
Cause analysis:
1, water is not enough, start the protection against dry burning;
2. Double-plugged power cord One power cord is not inserted correctly (bottom-heated soymilk machine);
Solution:
1, and the water quantity must be in the middle of the upper and lower scale lines;
2. Confirm that the power cord is plugged in again;
Fault 4: Key failure
Cause analysis:
1, the lamp board is affected with moisture, and the keys are rusted or oxidized, resulting in failure to work normally;
2, the computer board is affected with damp, and the chip program is chaotic;
3. Water enters the machine, causing local short circuit of the computer board;
4. The data cable of the lamp board is in poor contact with the socket of the computer board.
Solution:
1, replace the key or light board;
2. Dry the moisture in the computer board and the machine with the cold wind gear of the hair dryer, or replace the computer board;
3. Check whether the connection between the data cable of the lamp board and the computer board is good.
Fault 5: The indicator light is not on.
Cause analysis:
1, the indicator light interface is loose or has poor contact;
2. The indicator light is damaged;
3. The lamp board is affected with damp, resulting in oxidation and rust of lamp feet.
Solution: Replace the lamp board.