food with plastic packaging containers tools and other products are not required.
3 3.1.2 .3 local environmental protection department issued by the certificate of compliance with the requirements. Relax the requirements of environmental protection certification, the following can be: (1) environmental protection departments in the EIA report based on the approval of the enterprise construction project and the acceptance of the opinions after the construction of the plant; (2) emissions licenses and noise composite requirements of the certificate; (3) environmental monitoring reports.
4 3.1.2 .7 Product type inspection report.
( 1 ) type inspection report can be completed by the enterprise itself can also be entrusted to a qualified inspection agency to complete, but it must be the same batch of products, that is, all the items are reflected in a report.
( 2) If the enterprise in the verification site can not provide the type test report, the verification team to continue field verification work, but the enterprise should be submitted within the specified time type test report, or else is considered to be reported incomplete materials.
5 3.1.2 .8 product instructions or product labeling.
Enterprises can be based on the characteristics of their products, must state the content of the impact on personal health and safety, other at-a-glance content can be simplified, but shall not be simplified because of its instructions or labels to the user inconvenience or harm.
6 3.2.2 Enterprises trial production of products must be designated by the State Administration of Quality Supervision, Inspection and Quarantine inspection agency based on the corresponding product specifications batch test.
By the General Administration of the eight designated licensing inspection agency for the factory inspection program for batch testing. "Enterprise trial production of products," including the new enterprise products and licensed enterprises to add products.
7 enterprises do not have the ability to test the key control test items, should be sent every 3 months to the AQSIQ designated inspection agency for inspection.
The AQSIQ designated inspection agency refers to the 86 designated certification inspection agency.
8 7.6 Enterprises in the sampling, supervision and inspection or their quality has been complained of when the product testing has failed items. The above provisions of the "sampling, supervision and inspection" is the provincial supervision and inspection, municipal regular supervision and inspection, national supervision and inspection, special inspection.
9 "Rules" field verification methods for only part of the process of production enterprises, such as bag making, packaging plants, assembly plants, etc. 1, field verification, production equipment, inspection equipment, etc., the requirements only include the content of the process.
2, the production license certificate of such enterprises will be specified in the product variety of limited processes.
3, on the bag factory, packaging plant: type test report can be recognized by its upstream enterprise product reports; field verification of qualified samples need to be licensing inspection.
2.2.8 workshop to establish personnel in and out of the logistics channel, personnel should be sterilized, dust removal or air shower (bath) and other devices, work clothes should be kept clean. All kinds of food plastic packaging containers and tools and other products production enterprises should have personnel access and logistics channel, personnel channel should have changing, disinfection, dust and other facilities. Logistics channel should be isolated from the production area, and have a segregated area compatible with the production. Transportation of materials shall not enter the production area, production area staff shall not enter and exit from the logistics channel. Direct packaging of imported food packaging containers and tools and other products such as cling film, composite film, disposable tableware, beverage bottles or drinking buckets and other production enterprises disinfection facilities requirements: hand-washing facilities should be inductive or foot-operated, to avoid cross-pollution; disinfection should be done to disinfect the alcohol and other disinfection. Buffer zone should be regularly disinfected by ultraviolet irradiation. Work clothes should include hats, gloves (if it is not convenient to use gloves to work, should be in the work of regular disinfection of hands), full body work clothes, change shoes or wear footwear. And should have wind shower facilities (beverage bottles or drinking buckets production enterprises can use the wind screen, combined with the positive pressure of the plant).
Production of non-directly imported packaging containers tools and other products such as production enterprises such as diamine tableware, plastic chopping boards, etc., should at least use hand sanitizer to wash their hands, and should have at least such as dust removal rollers and other dust removal facilities. Clean work clothes should be worn. For the following three types of products, wind showers are required: ( 1) cling film ( 2) disposable tableware ( 3) laminated film bags changing and hand washing facilities are required and should be at the entrance to the production area.
10 "Rules" field verification approach 2.3 production facilities 1 enterprises must have to meet the production needs of the workplace and production facilities, and well-maintained.
2 There should be cleaning, disinfection, dust control, anticorrosion, ventilation, dirt disposal and other facilities that are compatible with the products produced and well maintained. Production facilities do not include production equipment, mainly refers to production equipment outside and directly related to the normal production of facilities such as handling facilities, ventilation facilities, material handling facilities. Workplace refers to the space and area sufficient for production needs. Packaging containers and tools for direct packaging of imported food products such as cling film, composite film, a
Tableware and other production enterprises should be closed production, and with the closed production of appropriate ventilation and dust prevention facilities. Production of non-directly imported packaging containers and tools and other products such as production enterprises such as diamine tableware, plastic chopping boards and other production enterprises, should also have with the production of appropriate dust ventilation facilities. Such as exhaust fans.
11 3.3.4 inspectors should be familiar with the product inspection regulations, with the work appropriate quality and safety knowledge, skills and appropriate qualifications.
The corresponding qualifications refer to the induction of training, either internal or external training.
12 5.4 Package labeling.
Such as bottles, cups, cutlery, chopping boards and other products with clear food use purposes, its packaging labels or instructions may not be added to the food labeling. Such as other non-composite film, composite film and other products that are easy to confuse with non-food products should be in its product packaging or labeling the word "food". Internal call and not for sale of products, such as the workshop line production products or products that have not left the workshop, may not indicate the "food" logo, call or additional packaging ex-factory products from other places must be indicated on the outer packaging.
13 6.1 Inspection management should be recognized in the quality and safety management system, "quality inspection department has the right of veto on product quality", the quality inspection department should be able to objectively and truthfully determine whether the product is qualified according to the test data and issue the corresponding report, other personnel shall not artificially interfere with the results of the determination.
14 "Rules" (a) non-composite film bags 1 . Licensing product range of enterprises will be ordinary biaxially oriented polypropylene film products after heating sealing directly used for packaging food according to heat-sealed biaxially oriented polypropylene film processing to increase a product variety: gb/t 10003-1996 ordinary bopp film, such as the enterprise purchased a single film only after printing that is sold, the temporary non-licensing. Production of single film, only for the company's composite film production, single film also need to apply for a license.
15 4 . Product standards and related standards Table 2 non-composite film in the polyvinylidene chloride sheet enteric coating film related standards increased gb15204-1994 "food containers, packaging materials with vinylidene chloride - vinyl chloride *** polyresin hygiene standards" 16 7.1 Licensing inspection sampling method Table 4 polyethylene self-adhesive cling film: randomly selected 3 volumes should be changed to 6 volumes; retail commodity bags and chain-link self-sealing bags: are Should be taken from 3 boxes respectively 30 × 2 (bag specifications should not be less than 15 × 15 cm, or draw some of the film as a supplement to the unmanufactured bags).
17 7.3 Rules for determination of fresh bags according to commodity retail bag test, the thickness of the project does not evaluate.
18 "Rules" (II)
Laminated film bags 1 . Licensing product range to avoid confusion, the 9th composite film products, "multilayer composite food packaging film, bags" to "other types of composite food packaging film, bags". Enterprises must have a record of enterprise standards, and enterprise standards of health indicators shall not be lower than the inner layer of similar material products of the national standard, the rules of the requirements. Color printing plant purchased composite film by printing directly after the sale, the temporary license is not issued.
19 2.2.3 key process control maturation room should be from the lower part of the air intake, upper exhaust. No requirements for the form,
only that it does not affect the ripening temperature and time.
20 4. Product standards and related standards Table 2 liquid food preservation packaging with paper-based composite materials (roofing packages) related standards refer to product standards 21 6. Mandatory factory inspection equipment Table 3 other categories of multilayer composite film bags mandatory factory inspection equipment read 1. tape measure or ruler or vernier calipers; 2. material testing machine; 3. magnifying glass 22 7.1.1 Enterprises applying for the following four kinds of composite film bags Products, according to the following technical requirements of the order of high and low to extract two high technical requirements of the product for licensing inspection such as enterprises at the same time the production of 7.1.1 in the four kinds of samples, but the sampling, the finished product warehouse, no boiling-resistant composite film bags, composite film bags for packaging of squash, and only extracted to the four kinds of composite film bags of the latter two samples, the licensing of the product varieties do not include boiling-resistant composite film bags and composite film bags for packaging of squash, cooking-resistant composite film bags and composite film bags for packaging of squash, and boiling-resistant composite film bags and composite film bags for packaging of squash, and the product types are not included. Composite film bags and pickled mustard packaging with composite film bags to do another addition to the processing.
23 7.1. Sampling method composite bags: should be taken from 3 boxes of 30 × 2 (bag specifications should not be less than 15 × 15 cm, or take some of the film is not bagged as a supplement). Involving micro-inspection indicators, should be sealed separately, directly to the micro-inspection personnel, to avoid contamination of the sample transfer process.
24 8. qs logo labeling enterprises should be licensed within 12 months after the appropriate part of its licensed products printed non-removable qs logo. Changed to: in its license within 12 months after the appropriate parts of the licensed product, or outer packaging box (bag products) or paper core (rolls of finished products) printed non-removable qs logo.
25 "Rules" (IV)
Woven bags 7 . Sampling methods such as enterprises said that the production of plastic woven bags and composite plastic woven bags at the same time, but in the field verification of the composite plastic woven bag samples are not available, only plastic woven bags, the licensing of product varieties are only included in the plastic woven bags, composite plastic woven bags to do another addition to the processing.
When the enterprise at the same time the production of polyethylene, polypropylene woven bags should be taken samples.
26 "Rules" (V)
Container products 1. Licensing product range: "plastic bottles, plastic drinking cups (jugs), plastic bottle blanks" to "plastic bottles, plastic drinking cups (jugs), plastic bottles (blanks)"
Various shapes of plastic containers can be used multiple times according to the plastic bottle application.
The production of preforms, used only in the case of the Company's production of beverage bottles, preforms also need to be licensed, but do not need to develop enterprise standards and type inspection, only process quality control.
27 3 . Necessary production equipment Table 1 Plastic anti-theft bottle caps necessary production equipment injection molding machine read: injection (pressure)
plastic machine.
28 6 . Necessary factory inspection equipment Table 3 polyester (pet) non-vapor beverage bottles deleted: verticality deviation tester.
29 Plastic anti-theft bottle cap Delete: projector 30 1, 2, 3 products measuring cylinder can be replaced by a balance.
31 7.1 Sampling method Table 4 polyethylene blow molded drums sampling number 20 to: 28 32 8 . qs logo labeling changed to: 12 months after its certification in the appropriate parts of the mold of its certified products, packaging, labels or instructions to print (paste) qs logo on their own. Direct-to-consumer products, such as plastic bottles, plastic drinking cups, in its smallest sales package, instructions or products printed (paste) qs mark.
The qs Mark can be colorless when molded into a mold.
33 test items of the single evaluation of the three pet bottles of vertical load pressure, volume deviation of hot-filled bottles and the minimum wall thickness only issued data, do not do the evaluation of the 34 "Rules" (F)
Tools for food 1 . The scope of licensing products 1, limited to polypropylene ( pp ), polystyrene ( ps ) two materials; 2, including blister and other thermoformed lunch boxes, bowls, plates, dishes, cups, lids; 3, including blow molding of disposable food and beverage utensils; 4, including injection molding of disposable food and beverage utensils, such as instant noodle cups, ice-cream cups; 5, excluding yogurt cups, jelly cups, knives, forks, stirring rods, straws; 6, not including a variety of Blister of cookies, vegetables, seafood, etc., such as the production of such products such as their own sheet processing after the enterprise, you can
against the rules of the first application for a production license of the sheet.
35 4 . Product standards and related standards Table 6 disposable plastic food and beverage product standards and related standards added: gb 18006.1-1999 disposable biodegradable food and beverage general technical conditions 36 6 . Necessary factory inspection equipment Table 9 disposable plastic food and drink utensils to delete the metal plug gauge, Shore hardness tester37 7.1 from the warehouse of the manufacturer, randomly select the leading product a specification for licensing inspection. The same raw materials, the same specifications, the same process for a batch of products. Finished product warehouse from the production enterprises, from each product variety, randomly selected from its leading products of a specification for licensing inspection. The same raw materials, the same specifications, the same process for a batch of products.
38 7.1.3 sampling method disposable plastic food and drink utensils to increase: If there are different materials, each material needs to be sampled.
39 7.2 test items disposable plastic tableware licensing test items polystyrene ( ps ) temperature resistance can only report test data, not for individual evaluation.
................. You make a reference to it, because I do not know what products you specifically.