Kitchen ceiling fastening board how to buckle good
1: Later, the edge will be nailed in the wooden wedge, and maintain the level, with screws to tighten the edge line. Edge line installation, dining room kitchen around the edges of the line needed for each according to the true specifications of the wall laser cut well, in the wall fill pop-up straight line, and in the horizontal line every 30cm to do the hole marking, hole depth of 40mm up and down, followed by the wooden wedge will be punched into the hole.
2: solid, below the set of silk rod adjusted to a good relative height, and screws will be silk rod and three eight main keel fixed immovable. Roof rod expansion set installation, with a soft ruler from the roof ceiling ceiling measurement of the appropriate hole installation point, and make a good mark, with a special tool to make a straight _ 8mm, 40mm deep before and after the hole, according to the relative height of the decoration ceiling defective rod length, and will have expansion set of rod rod inserted into the hole at one end, twisting the nut.
3: the installation of the main keel, with the bolt will ceiling keel fixed immobile in the expansion sleeve below the silk rod, and then in the ceiling keel effectively spread all over the part of the hanger installed, and then install the triangle keel, triangular keel spacing is generally in the 300mm above and below the ceiling keel and triangular keel set of dead pieces, according to the hanger will make them immobile coupling. And buckle plate installation should be based on the construction site of the pipeline holes. Range hood piping electric water heater piping installation, installation of the main keel, is the installation of piping, first install the piping and then install furniture panels.
4: aluminum buckle plate installation, installation to the second aluminum buckle plate to go, when the first do not have to install, should be other aluminum buckle plate, household appliances installed, and to ensure that the overall leveling, the gap is consistent, and then after the installation of the second piece of buckle plate. Aluminum buckle plate stuck on the triangular keel, step by step installation, installation to maintain the seam gap is consistent, pay attention to the four corners of the buckle plate to be aligned at both ends, and will be the edge of the corner of the network run into 60 angle, rate of European version and the edge of the corner line should be maintained flat.
What are the acceptance criteria for kitchen ceiling grommet installation
1, grommet decoration ceiling installation of various main keel decoration ceiling must be stable and solid, fixed after the end of not moving, to achieve a full range of monitoring and straightening, and check the installation part is not appropriate;
2, grommet decoration ceiling installation project commonly used raw material types, specifications and models, colors and their Substructure, fixed immobile way should meet the design regulations; canopy wood frame construction should meet the fire safety regulations;
3, wood frame commonly used wood specifications should be in accordance with the design provisions of the middle of the construction of wood should be smeared with glue continue to use nails to fix immobile, and the side of the PVC button board touch must scrape flat; PVC button board should not have bubble, peeling, cracks, missing corners, stains and pattern design shortcomings such as damage, the surface layer should be leveled, the edge of the board should be smooth and smooth. The surface should be flat, the edge should be flush, the color should be consistent; perforated aluminum holes should be sorted flush, man-made boards, wooden plywood can not be open glue, lose color and rot;
4, PVC fasteners should be bracketed or brush latex paint, the interface should be brushed with white glue adhesive paste fine cotton cloth, joints on both sides of the minimum of each rebar overlap of 5mm; man-made boards such as brushing and coating of water-based paint, the neighboring surfaces of the wood grain and color should be similar; man-made boards such as water-based paint, wood grain and color should be similar; the touch side must be scraped flat. Color should be similar; man-made boards, MDF, such as the use of nails fixed immovable, nail distance of 80-100mm, nail length of 25-35mm, the nail cap should be hit the back of the head flat and into the surface of the 0.5-1mm, the nail eye with the food oil-based putty powder smoothing.