Current location - Recipe Complete Network - Catering training - Detailed description: Installation and acceptance of cabinet
Detailed description: Installation and acceptance of cabinet
"Three-point quality and seven-point installation of cabinets" shows that installation is the last step and the most critical step in customizing product cabinets.

fixed

Install grounding cabinet:

a)? First, install the adjusting leg under the ground cabinet (the material of the adjusting leg is non-slip). Throughout the installation process of the cabinet, the ruler of the master worker never leaves his hand. First, fix the adjusting leg on the cabinet, then adjust the height of the adjusting leg according to the design and construction drawing of the cabinet, and wait for the installation of the skirting line at the back.

Tips:

Please note that when installing the floor cabinet to adjust the legs,

The height should be consistent, and the overall horizontal height of the cabinet should be consistent after installation. There must be design drawings during installation and construction, and workers should carry out construction according to the design and construction drawings of cabinets, and installation at will is not allowed.

This case is special. There is an arc shelf design in the corner of the cabinet, which will expose some adjusting legs.

For the exposed part, copper adjusting feet can be placed, which will not affect the overall appearance. Brand store: Yubang cupboard bathroom cupboard

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

b)? Place and adjust the position of the lower cabinet. Measure the actual size of the cabinet according to the size of the design drawing, determine the position of each cabinet, and place the cabinet with adjusting legs. The constructors arranged the cabinets designed according to the drawings, and compared them with the drawings according to the actual situation on site. For example, when the cabinets are placed, the cabinets of the drain basin and the cooker should be determined according to the positions of the water pipe and the gas pipe.

When encountering problems that are not in conformity with the actual design, we should contact the designers in time and correct them in time. c)? Do not insert the backplane. Some brands of cabinets will choose whether to keep the baffle on the back of the cabinet according to the needs of customers. If there are reserved power sockets or other pipes on the back of the cabinet, the baffle may not be inserted.

After confirming the removal and retention of the backplane, you can connect the cabinet. Links: rave reviews, cabinets, and big recommendations make you fall in love with the kitchen.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

D) Tighten the lower cabinet. Use an impact drill to drive copper nails into each group of ground cabinets and fix them to each other, so that the cabinets form a whole.

E) Fix the layered partition in the cabinet. In order to ensure the stability of the clapboard, the clapboard of the lower cabinet is fixed with a white plastic clip to avoid loosening, which will cause the items on the upper part of the clapboard to fall.

Note: where there is gas pipeline, the partition needs special treatment. Workers need to measure the diameter of the pipeline, then cut a gap, wrap the gap with aluminum foil paper, and install a partition so that the newly cut gap just blocks the gas pipeline.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

F) Install the lower cabinet door panel. After the partition of the ground cabinet is installed, install the cabinet door panel. Let's see how our host does it.

When installing the door panel, measure the size of the cabinet and the door panel with a ruler and a meter ruler, mark the door panel with a pencil, and then tighten the screws with an electric drill to fix the cabinet and the door panel.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Hanging cabinet installation:

The installation of hanging cabinets is very similar to that of ground cabinets, but the difference is that hanging cabinets need to be fixed on the wall, and there are more processes than ground cabinets. How to do the extra process? Let's follow the installation hero.

a)? Determine the installation position of the hanging cabinet. According to the design drawings, measure the wall size of the hanging cabinet, then measure horizontally and vertically according to the distance on the drawings, measure the distance between the upper and lower cabinets, determine the position of the pendant, and draw a line on the wall.

Note: the installation position of the hanging cabinet should be the same as that of the ground cabinet.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

b)? Wall hanging pendant. Before installing the hanging cabinet, it is necessary to drill holes on the measured wall. After drilling a hole with an electric drill, put the expansion pipe into the hole, then put the hanger in place and pass through the hanger, and drill the screw into the expansion pipe with an electric drill.

Note: When choosing the expansion tube and screw, we should also pay attention to the length matching according to our own wall thickness. Owners who have already posted wall tiles need to pay attention to the length problem at this time. The length of the expansion pipe and the screw must be greater than the thickness of the wall brick to ensure that the screw can enter the wall. This can play the role of anti-skid and stability, and the hanging cabinet will not fall off for a long time to ensure safety.

Tips:

Pay special attention to the direction of water and electricity lines on the wall when punching holes. Once the water and electricity lines are hit, the consequences are unimaginable. Therefore, it is best to have hydropower workers or supervisors present when drilling, or have hydropower construction drawings. Only in this way can the safety of the through-wall drill be guaranteed.

c)? Hang the closet. It is very skillful to hang the hanging cabinet on the pendant. If you don't hang it firmly, there will be danger. Be careful when operating.

d)? Adjust the height of the hanging cabinet. Measure the distance between the upper and lower cabinets with a ruler. If the cabinets are different in height, use a screwdriver to adjust the screws on the back of the cabinets until the cabinets are horizontal. Then the white hanging code buckle can be buckled at the gap of the back plate of the hanging cabinet, and the hanging code buckle can play an aesthetic role.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

E) Fix the layered partition board in the cabinet and install the door panel of the hanging cabinet. The installation procedure of the hanging cabinet is basically the same as the partition and door panel of the ground cabinet.

Link: Daren explains the initial test, second test and installation process of cabinets in detail.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Desktop installation:

The installation of the countertop is not as simple as putting the stone directly on the lower cabinet and then sealing it with glue. In this case, the owner uses marble stone, and the cabinet workers first put a lining board on the lower cabinet (the lining board is an ordinary board, which is generally the same as the board used for cabinets), and then install the countertop.

Why do you want to add linings? Is it necessary?

Putting the countertop directly on the cabinet has great disadvantages. The contact part between the countertop and the cabinet is only the gables on both sides and the front and rear drawstrings, and the rest are suspended, which greatly reduces the use strength of the countertop and is easy to break and deform during use, so the lining plate is provided.

What is the function of the gasket? Which material should be chosen as the lining?

Add a liner under the countertop and the force will be balanced. The liner connecting box has compact and stable structure, strong impact resistance, good cushioning performance, and the desktop is not easy to crack and deform. The stability of the whole pad not only includes uniform stress, but also waterproof and moisture-proof, so it is best not to choose a large core board, because it has the weakness of being susceptible to moisture, mildew and deformation, and it is not environmentally friendly. Lushui river slab can be considered, and the thickness is generally ≥ 16mm, which is enough.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Do all installations require splicing countertops?

Because of the length of the mesa, sometimes the mesa splicing cannot be completed in the factory, and the on-site splicing is inevitable. The countertops of cabinets are usually cut in the factory. Just install the on-site splicing. The key is how to splice. Generally, the common integral cabinets are all straight lines, a U-shape and an L-shape. No matter what shape, there will always be the problem of table splicing. If the cabinet is L-shaped, the method of 45-degree stone cutting and splicing is generally adopted.

Attention should be paid when splicing: the glue is evenly distributed to avoid glue leakage, and there is no glue or less glue in some places, which affects the bonding effect; Be sure to wait until the glue is completely dry when polishing. If the glue is not completely dried, the next process will be carried out, and the bonding effect will also be affected.

Install the countertop, first put the inner container on the lower cabinet, straighten it, and then install the countertop on the inner container. Don't apply any glue, try the effect and see if it is suitable. If the installation area is not a complete square, the countertop may need to be trimmed. Connect the seams of the desktop with glass glue. After checking all the corners, you can start bonding materials. Use 100% cleaning silicone adhesive, which is very sticky and will not fade on light marble. Avoid using dark binders, because once dried, their colors will show through the marble. Then it is polished with sand skin. Generally, there is no trace at the splicing place, which is relatively flat and smooth. Finally, the countertop is sealed, and the seams around the countertop and the wall are sealed with glass glue.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Decoration of gas pipeline and oil fume pipeline

Measure the length of the pipeline to be wound, then select the board ruler with the same material as the cabinet to draw lines, and then cut along the line with the cutting machine. Apply glue to the cut board, air-dry it for a few minutes, and then bond it. Then wrap the bonded board in the pipeline, and adjust the position to make the corners of the board contact with the wall. Finally, seal the frame with glass glue.

Tips:

Generally, the skirting line will be installed on the ceiling at the top, so when cutting the pipeline at the top of the package, we should also pay attention to leaving the position of the skirting line to ensure that the package is complete and beautiful, and the package board is close to the wall.

Install the door handle, hat line and skirting board.

In fact, the installation of the door handle is very simple. First of all, we should choose the installation position of the handle according to the requirements of the owner or designer, such as whether it is placed in the center or near the door, then mark the position where the door handle should be placed with the template, and then punch holes in the marked position. When drilling, be careful not to touch the frame of the hanging cabinet. It is best to use wooden temples on the inside of the door panel. Put the screw into the good hole, the nut eye of the handle is facing the screw, and tighten the screw with an electric drill.

The installation of cap line and skirting board is relatively simple, and the most important thing is to calculate the size. A good installation master not only installs the cabinets firmly and beautifully, but also saves materials. The master first measured the length with a meter ruler, then calculated the material, marked and crossed the measured length on the material, and cut it at the marked place. Glue the cut hat line or skirting board to the cabinet, and then fix it with air nails.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

check before acceptance

After the installation of cabinets is completed, not everything is settled, and there are more arduous tasks waiting for our owners. What link? That is acceptance! Let's take a look at the items that should be checked during the acceptance.

1)? The external surface of the product should be kept intact, and there should be no damage such as bumps, scratches, cracks and indentations.

2)? The installation position of cabinets should be based on the design drawings of household kitchen equipment, and the position should not be changed at will.

3)? The cabinets should be placed in harmony, and the level should be guaranteed after the combination of the countertops and hanging cabinets.

4)? The door panel should be fully adjusted so that the door panel is neat up and down, front and back, left and right, and the gap is even.

5)? Artificial stone countertops should be seamlessly spliced.

6)? The gap between doors and frames, doors and gates, drawers and frames, drawers and gates, and adjacent surfaces of drawers and drawers shall be 2.0 mm. ..

7)? The combined installation of the hanging cabinet and the wall surface should be firmly combined, the connecting screws should be no less than M8, and there should be no less than two connecting fixing points every 900mm to ensure that the bearing requirements are met.

8)? The countertop and cabinet should be firmly combined and not loose.

9)? Joints of drainage mechanism (water filter, overflow nozzle, drain pipe, pipe connector, etc.). ), the connection between the water tank and the drainage interface should be tight, and there can be no leakage. Hose connecting parts shall be fixed with clips.

10)? The joint between the rear retaining water and the wall shall be sealed with sealant.

1 1)? The joint between stainless steel sink and countertop should be sealed with sealant.

12)? The joint between the embedded cooker and the countertop should be smooth.

13)? All drawers and baskets should be pushed and pulled freely, without blocking, and there are limit element protection devices that will not be pulled out of the cabinet.

14)? The sharp corners of all cabinets should be dulled.

15)? Metal parts should be placed where people can touch them, and burrs and sharp corners are not allowed.

In addition: site installation should be civilized. Before the construction, clean up the site and remove the sundries that hinder the construction, so as to facilitate the construction. After the installation is completed, clean up and rectify the site in time. After acceptance, it will be delivered to customers for use.

Link:

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

E) Fix the layered partition in the cabinet. In order to ensure the stability of the clapboard, the clapboard of the lower cabinet is fixed with a white plastic clip to avoid loosening, which will cause the items on the upper part of the clapboard to fall.

Note: where there is gas pipeline, the partition needs special treatment. Workers need to measure the diameter of the pipeline, then cut a gap, wrap the gap with aluminum foil paper, and install a partition so that the newly cut gap just blocks the gas pipeline.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

F) Install the lower cabinet door panel. After the partition of the ground cabinet is installed, install the cabinet door panel. Let's see how our host does it.

When installing the door panel, measure the size of the cabinet and the door panel with a ruler and a meter ruler, mark the door panel with a pencil, and then tighten the screws with an electric drill to fix the cabinet and the door panel.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Hanging cabinet installation:

The installation of hanging cabinets is very similar to that of ground cabinets, but the difference is that hanging cabinets need to be fixed on the wall, and there are more processes than ground cabinets. How to do the extra process? Let's follow the installation hero.

a)? Determine the installation position of the hanging cabinet. According to the design drawings, measure the wall size of the hanging cabinet, then measure horizontally and vertically according to the distance on the drawings, measure the distance between the upper and lower cabinets, determine the position of the pendant, and draw a line on the wall.

Note: the installation position of the hanging cabinet should be the same as that of the ground cabinet.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

b)? Wall hanging pendant. Before installing the hanging cabinet, it is necessary to drill holes on the measured wall. After drilling a hole with an electric drill, put the expansion pipe into the hole, then put the hanger in place and pass through the hanger, and drill the screw into the expansion pipe with an electric drill.

Note: When choosing the expansion tube and screw, we should also pay attention to the length matching according to our own wall thickness. Owners who have already posted wall tiles need to pay attention to the length problem at this time. The length of the expansion pipe and the screw must be greater than the thickness of the wall brick to ensure that the screw can enter the wall. This can play the role of anti-skid and stability, and the hanging cabinet will not fall off for a long time to ensure safety.

Tips:

Pay special attention to the direction of water and electricity lines on the wall when punching holes. Once the water and electricity lines are hit, the consequences are unimaginable. Therefore, it is best to have hydropower workers or supervisors present when drilling, or have hydropower construction drawings. Only in this way can the safety of the through-wall drill be guaranteed.

c)? Hang the closet. It is very skillful to hang the hanging cabinet on the pendant. If you don't hang it firmly, there will be danger. Be careful when operating.

d)? Adjust the height of the hanging cabinet. Measure the distance between the upper and lower cabinets with a ruler. If the cabinets are different in height, use a screwdriver to adjust the screws on the back of the cabinets until the cabinets are horizontal. Then the white hanging code buckle can be buckled at the gap of the back plate of the hanging cabinet, and the hanging code buckle can play an aesthetic role.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

E) Fix the layered partition board in the cabinet and install the door panel of the hanging cabinet. The installation procedure of the hanging cabinet is basically the same as the partition and door panel of the ground cabinet.

Link: Daren explains the initial test, second test and installation process of cabinets in detail.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Desktop installation:

The installation of the countertop is not as simple as putting the stone directly on the lower cabinet and then sealing it with glue. In this case, the owner uses marble stone, and the cabinet workers first put a lining board on the lower cabinet (the lining board is an ordinary board, which is generally the same as the board used for cabinets), and then install the countertop.

Why do you want to add linings? Is it necessary?

Putting the countertop directly on the cabinet has great disadvantages. The contact part between the countertop and the cabinet is only the gables on both sides and the front and rear drawstrings, and the rest are suspended, which greatly reduces the use strength of the countertop and is easy to break and deform during use, so the lining plate is provided.

What is the function of the gasket? Which material should be chosen as the lining?

Add a liner under the countertop and the force will be balanced. The liner connecting box has compact and stable structure, strong impact resistance, good cushioning performance, and the desktop is not easy to crack and deform. The stability of the whole pad not only includes uniform stress, but also waterproof and moisture-proof, so it is best not to choose a large core board, because it has the weakness of being susceptible to moisture, mildew and deformation, and it is not environmentally friendly. Lushui river slab can be considered, and the thickness is generally ≥ 16mm, which is enough.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Do all installations require splicing countertops?

Because of the length of the mesa, sometimes the mesa splicing cannot be completed in the factory, and the on-site splicing is inevitable. The countertops of cabinets are usually cut in the factory. Just install the on-site splicing. The key is how to splice. Generally, the common integral cabinets are all straight lines, a U-shape and an L-shape. No matter what shape, there will always be the problem of table splicing. If the cabinet is L-shaped, the method of 45-degree stone cutting and splicing is generally adopted.

Attention should be paid when splicing: the glue is evenly distributed to avoid glue leakage, and there is no glue or less glue in some places, which affects the bonding effect; Be sure to wait until the glue is completely dry when polishing. If the glue is not completely dried, the next process will be carried out, and the bonding effect will also be affected.

Install the countertop, first put the inner container on the lower cabinet, straighten it, and then install the countertop on the inner container. Don't apply any glue, try the effect and see if it is suitable. If the installation area is not a complete square, the countertop may need to be trimmed. Connect the seams of the desktop with glass glue. After checking all the corners, you can start bonding materials. Use 100% cleaning silicone adhesive, which is very sticky and will not fade on light marble. Avoid using dark binders, because once dried, their colors will show through the marble. Then it is polished with sand skin. Generally, there is no trace at the splicing place, which is relatively flat and smooth. Finally, the countertop is sealed, and the seams around the countertop and the wall are sealed with glass glue.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

Decoration of gas pipeline and oil fume pipeline

Measure the length of the pipeline to be wound, then select the board ruler with the same material as the cabinet to draw lines, and then cut along the line with the cutting machine. Apply glue to the cut board, air-dry it for a few minutes, and then bond it. Then wrap the bonded board in the pipeline, and adjust the position to make the corners of the board contact with the wall. Finally, seal the frame with glass glue.

Tips:

Generally, the skirting line will be installed on the ceiling at the top, so when cutting the pipeline at the top of the package, we should also pay attention to leaving the position of the skirting line to ensure that the package is complete and beautiful, and the package board is close to the wall.

Install the door handle, hat line and skirting board.

In fact, the installation of the door handle is very simple. First of all, we should choose the installation position of the handle according to the requirements of the owner or designer, such as whether it is placed in the center or near the door, then mark the position where the door handle should be placed with the template, and then punch holes in the marked position. When drilling, be careful not to touch the frame of the hanging cabinet. It is best to use wooden temples on the inside of the door panel. Put the screw into the good hole, the nut eye of the handle is facing the screw, and tighten the screw with an electric drill.

The installation of cap line and skirting board is relatively simple, and the most important thing is to calculate the size. A good installation master not only installs the cabinets firmly and beautifully, but also saves materials. The master first measured the length with a meter ruler, then calculated the material, marked and crossed the measured length on the material, and cut it at the marked place. Glue the cut hat line or skirting board to the cabinet, and then fix it with air nails.

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.

check before acceptance

After the installation of cabinets is completed, not everything is settled, and there are more arduous tasks waiting for our owners. What link? That is acceptance! Let's take a look at the items that should be checked during the acceptance.

1)? The external surface of the product should be kept intact, and there should be no damage such as bumps, scratches, cracks and indentations.

2)? The installation position of cabinets should be based on the design drawings of household kitchen equipment, and the position should not be changed at will.

3)? The cabinets should be placed in harmony, and the level should be guaranteed after the combination of the countertops and hanging cabinets.

4)? The door panel should be fully adjusted so that the door panel is neat up and down, front and back, left and right, and the gap is even.

5)? Artificial stone countertops should be seamlessly spliced.

6)? The gap between doors and frames, doors and gates, drawers and frames, drawers and gates, and adjacent surfaces of drawers and drawers shall be 2.0 mm. ..

7)? The combined installation of the hanging cabinet and the wall surface should be firmly combined, the connecting screws should be no less than M8, and there should be no less than two connecting fixing points every 900mm to ensure that the bearing requirements are met.

8)? The countertop and cabinet should be firmly combined and not loose.

9)? Joints of drainage mechanism (water filter, overflow nozzle, drain pipe, pipe connector, etc.). ), the connection between the water tank and the drainage interface should be tight, and there can be no leakage. Hose connecting parts shall be fixed with clips.

10)? The joint between the rear retaining water and the wall shall be sealed with sealant.

1 1)? The joint between stainless steel sink and countertop should be sealed with sealant.

12)? The joint between the embedded cooker and the countertop should be smooth.

13)? All drawers and baskets should be pushed and pulled freely, without blocking, and there are limit element protection devices that will not be pulled out of the cabinet.

14)? The sharp corners of all cabinets should be dulled.

15)? Metal parts should be placed where people can touch them, and burrs and sharp corners are not allowed.

In addition: site installation should be civilized. Before the construction, clean up the site and remove the sundries that hinder the construction, so as to facilitate the construction. After the installation is completed, clean up and rectify the site in time. After acceptance, it will be delivered to customers for use.

Link:

Cabinet Installation Villa Design Board Glass Marble Socket Stainless Steel Kitchen Equipment Glass Brick Drawer Cabinet Door Glass Cabinet Craft Glass Stainless Steel Cabinet Floor Cabinet Stainless Steel Integral Cabinet Glass Cabinet Door Panel Kitchen Wall Brick Kitchen Cabinet Door Marble Cabinet Glass Door Kitchen glass sliding door.