Step one: before installing the panel bed to carefully read the installation drawings, and prepare common tools, such as flat crosshead screwdriver, hammer and so on. After unpacking the parts package is best not to get confused, if similar parts are more, the drawings will draw a comparison of the physical size of the map, the parts not used to fork, it is very easy to distinguish between the various parts. Closet cabinet body (closet inside the partition, drawers, hardware connectors, wood _, hinges, slides and so on. Separate out and assemble the interior separate pieces such as the individual drawers, coat and pants racks, etc. Put them on the side.

The second step: check whether there is damage to the cabbage

Also check whether there is damage to the plate, if so, you should contact the merchant to make up the pieces. The place where all the screws, eccentric parts, and wooden shafts are to be installed will have guide holes, and there is no need to worry about the positioning of the parts. In the wrong parts, found that the screwing is not right do not brute force to continue to use, to find out whether the wrong use. And can not be repeated a part screwing, or easy to damage the plate, the installation will often appear unstable, tilt and other phenomena.

The third step: the bottom plate installation.

The first thing to do is to install the bottom plate, plate type bed mainly rely on the bottom plate support, the bottom plate is not installed, the whole plate bed may be shaky, are very unstable, especially uncomfortable to sleep, and affect the service life. Align the various interfaces on the base plate, then install the base plate, and then gently shake with your hand to see if there will be the bottom is not uneven and unstable. If the bottom board of the slatted bed is a drawer, you can not have to install the drawer first, the frame of the slatted bed will be determined, leave a good space on it.

Step 4: Backboard installation.

When the backboard of the panel bed is installed, the main thing is to make sure that the angle of the backboard and the bottom board is 90 ° right angle, and do not have a tilt.

Step 5: side panel top panel.

The side panel top plate of the panel bed is very important, install the base plate back plate, then you need to install the side panel of the panel bed. Side panels are able to connect the floor and the backboard of the slatted bed boards, slatted beds in the angle between the side panels are presented in the form of a right angle. When installing the top board, pay attention to the position of the back of the section is stable, to fix the top board firmly.

Step 6: Remaining installation.

After the frame of the panel bed is installed, it is necessary to install the cabinet doors, clothes rests, hanging rods, laminates, and drawers and other components of the panel bed, which can be installed according to the signs on the installation instructions for the panel bed.

Second, the plate skeleton bed installation method:

Step one, connect the bed head side columns and bed end side columns,

Generally speaking it is four solid wood side columns, headboard and two of the long side columns in combination with the end of the bed and two short side columns connected. Next speak the holes for the pre-built metal parts to screw in the screw rods and insert wooden wedges in the remaining empty spaces.

Step 2: splicing headboard

First, the headboard and the head of the bed side columns are spliced together, put together a bed, pay attention to the headboard do not install the opposite. Then it is the end of the bed installation, the same as the head of the bed installation.

Step three, connecting the bed

With the bed help to connect the bed head and tail. First of all, one end of the bed gang into the end of the bed pre-screwed screw rod, stabilize the screws, and then connect the other end. Note that the hole position of the bed gang should also be proportional to the end of our bed, the general skeleton bed is the hole position is facing down, if the hole position is centered, you can just install.

Step four, install hardware fixings

The last thing is to check and tighten all the screws and other hardware fixings in the skeleton bed, and install reinforcements. Unpack the bag of the skeleton frame, connect the skeleton frame and the four corners of the bed on the reinforcement, tighten it. This is a great success, row of stone row of skeleton bed installation is completed