Popular course recommendation
Editing Basic Video Tutorial (Computer Edition) Editing Mobile Phone Short Video Making Zero Basic Introduction Tutorial Clip 30 Minutes Quick Introduction PC Edition Clip 3.3.0 Computer Edition System Introduction Tutorial Clip Transition Effect Making Tutorial:
1. Open the software and the teacher introduces four kinds of transition videos. The first is the transition around the mirror, the second is the transition up and down and left and right, the third is the occlusion transition, and the fourth is the transition along a straight line by using the posture of the characters. Please refer to the teacher's video demonstration for the specific effect. 2. Summarize the four steps of making the transition effect. The first step is to find the material connection point, the second step is to speed up the end of the first paragraph and the beginning of the second paragraph, the third step is to add appropriate sound effects to the transition, and the fourth step is to color the picture appropriately, as shown in the figure. 3. First demonstrate the production of rotating mirror, import three materials into the software, drag them into the timeline, adjust the beginning and end of each paragraph, and delete the waste lens. See the teacher's video demonstration for the specific operation. 4. Take a look at the effect after finishing the material, and then speed up the whole video basically. Select the video and click the regular variable speed to adjust the speed to 1.4 times the speed, as shown in the figure. 5. After the acceleration, find the connection point, import the music of the card point first, find the connection point according to the card point, and select the audio collection. The teacher directly uses a piece of music collected before to enlarge the time axis, find a position where the card point faces the audio, and select audio Ctrl+J to add a marker point, as shown in the figure. 6. Reduce the timeline, select the second material, drag it into the picture-in-picture track, enlarge the timeline, and find the connection point of two videos at the first card point, as shown in the figure. 7. Drag the second video backward, choose the first video to observe the composition angle of the picture, find the same composition picture in the second video, cut off the different parts in front, and drag the back part to the connection point, so that the transition between the two videos will be good. See the teacher's video demonstration for details. 8. Reduce the timeline, add video 3 in the same way, then find the same position in the character material, delete the unnecessary part in front, drag the rest to the card point, enlarge the timeline, select video 3, adjust the zoom ratio to 140%, and move the position to match the composition with video 2, as shown in the figure. 9. Look at the overall effect, adjust the size of video 3 to 135%. After the pictures are aligned, delete the redundant parts behind the video and delete the redundant parts of the audio. Select the film and television level of the filter, and the intensity of the blue-orange effect filter is 40, so that the transition will be fine, as shown in the figure. 10. The next step is to stop the transition, drag in two pieces of material, check the connection point of two videos, and use clothes as the cover. When the lens is completely covered, it can be used as a connection point. Similarly, as long as you find the same cover, you can use it as a video transition, as shown in the figure. 1 1. Go to the left-right swing and the up-and-down swing transition, and look at the joints of materials. The transition sound effect is directly added at the transition. Select the video and click the speed change, and accelerate at the end of the first video, as shown in the figure. 12. At the beginning of the second video, give it a slow speed drop, and then add a transitional sound effect under the accelerated video. Do the same operation later, and throw and enter when shooting video, as shown in the figure. 13. First, add a video, the lens swings upward, then continue to add a second video, slowly swing downward from the sky, cut off the waste, and then when the first video lens turns to the sky, start to accelerate, add three points at variable speed, pull the middle point upward, and turn off the original sound, as shown in the figure. 14. Delete the redundant pictures behind the first video and speed up when the second video falls from the sky. Customize the speed change at the beginning, add three curve points, and turn to characters to accelerate, as shown in the figure. 15. Add transition sound effects and audio sound effects at the connection point, select "transition" to add sound effects, enlarge the time axis, adjust the length of sound effects to suit the video, and delete the redundant sky clips in video 2 and the redundant clips in video 1, as shown in the figure. 16. Let's look at the transition of people walking. This is similar to loop conversion. Delete the abandoned shots in the three videos, accelerate each video to a stable trajectory, then find the connection point, superimpose the videos, and add appropriate music. The key point is that the speed of people walking in the picture is consistent with the speed of the mirror trajectory, and we should also pay attention to the secondary composition, as shown in the figure. How to make the transition effect of "cutting professional edition" The content of "Cutting and Mapping Transition Effect Making Tutorial" is shared here, I hope it is useful to you! As the official and practical video editing software of Tik Tok, Clipping can easily produce very interesting short videos, which is in line with the operating habits of young users who like to play short videos at present! Moreover, you also want to learn the cutting and screening operations to make cool and eye-catching short videos, so all-round software learning is essential. Click on the link: