Adjust and float the fishing bottom:

1. Rough bottom finding:

Do not hang the sub-line, and the lead skin seat is hung with heavy lead, and the weight of the lead skin is greater than the buoyancy of the float. All the floats are submerged in the water, and gradually pull up and float until one eye is exposed, and the uppermost space bean is next to the second space bean to complete the positioning.

2. Adjust the mesh:

The float is pulled down by 25cm, at this time, the float should be completely submerged, and gradually cut the lead skin until the required mesh is exposed.

3. Basic principles for setting the eye adjustment and fishing purpose:

7-mesh soft-tail floating and rubbing bait: 4-5 fishing for 2

7-mesh soft-tail floating and pulling bait: 3-4 fishing for 2

hard-thin-tail rubbing bait: 7-9 mesh, 2-3 mesh

hard-thin-tail pulling bait: 5-7 mesh. Fishing low, fishing spirit.

according to the weather, season, hook weight, bait specific gravity and bait ball size, fine-tune the above-mentioned adjustment.

4. Find the bottom accurately:

Hang the sub-line, move the float, adjust the distance between the position of the float seat and the position of the positioned upper space bean to be approximately equal to the length of the sub-line, lower the hook and rub the bait to hang a large bait ball to find the bottom (which is also nesting), so that the float is exposed to the water for 2 eyes, and continue to pull up the float for 2 cm. If the float shows more than 3 eyes, it means that it has passed the bottom, and the float is pulled back for 2.

adjustment process of trial fishing:

(1) If you have a mouth but no fish, you should pull up and float for 2CM (it can be pulled up for less than 5 times) if you catch fish in the upper lip for more than 2 times, you will find the right mouth.

(2) The middle fish is on the mouth or chin, which means that fishing is too dull. Pull up and float 1 cm at a time until the fish is in the upper lip for more than two times to find the right mouth.

(3) fishing without a mouth: every time you pull down the float for 15 cm, you can find the water layer where the fish is, which belongs to the category of fishing off the bottom-floating-fishing one standard deep. Let's talk about it in another way.

Lead-running fishing method:

1. Scope of application:

It is used when running water or small miscellaneous fish make hooks, and the fishing method is similar to traditional fishing.

2. Lead running and bleaching steps:

(1) When there is no hook, the heavy lead will come to the bottom.

(2) float down 2CM, and cut the lead skin until it is level.

(3) Open the upper space bean of the lead base for 3-5cm.

(4) Hook, pull up and float until 2-6 meshes are exposed, which can be used for fishing, and more meshes are exposed when the current is fast.

3. Precautions for running lead fishing

(1) In running water environment, try to choose large floats, which has strong positioning ability.

(2) The sub-line should be kept as short as possible within 1 cm, because lead fishing is extremely blunt, and short sub-line can amplify the signal.

(3) You should grasp the movements of going up and down, and you can both catch fish.

(4) The bait can be properly sticky.

Detailed steps for finding the mouth:

1. If the floating phase only rises slowly but has no mouth, or the floating phase only descends slowly after rising, it can be adjusted by pulling down until there is a slow rise and then there is a slight meal.

2. The drift phase only rises slowly, but there is no downward drift, so it is ineffective to adjust the fishing eye by pulling down the drift, which is mostly related to the bait state and size. You can adjust the bait state and bait application method in time before asking and exploring.

3. If the drift phase only rises slowly, but there is no drop-down drift, it is ineffective to adjust the fishing eye, bait state and bait application method, so you can reduce the lead and find a new mouth until there is a flat mouth and fish are caught.

4. The drift can't fall to the set fishing goal, or the high top doesn't fall for a long time. After eliminating the factors such as inaccurate rod throwing and bait loss, it is mostly caused by the fish interface. You can also pull down the drift to adjust or reduce the lead to find the mouth.

5. There are many fish in the nest, but there is still no mouth after adjusting the fishing orders. We should check the hook attachment rate and atomization rate of the bait. At the same time, it should be checked whether the fishing is too dull, drifting and fishing, and whether the bait falls into the mud layer with virtual bottom that the fish mouth does not recognize.

6. The adjustment of the dullness of the fishing eye is all without a mouth, and the adjustment of the bait state and the bait application method are also ineffective. We can reduce the lead, increase the adjustment of the eye, improve the bait carrying capacity of the drift, and enlarge the range of the adjustment and inquiry of the fishing eye, so that the bait has more layers to choose from at the virtual bottom, and then look for the mouth again until there is a simple slight mouth and the fish is caught.

7. After the drift rises slowly, it will suddenly stop. It belongs to a clear and normal phase, but it always misses the fish. It is related to the bait state, especially when the bait is too hard and too big. It is most common to adjust the bait state and the bait application method in time, and then go to ask questions.

8. The drift has a direct bite, but the pole can't catch the fish. You can adjust it by pulling it up, and you can find the standard straight bite and catch the fish.