1. First we cut out 6 to 8 leaf-shaped pieces of soft paper.

2. Fold them in half and glue their edges together to make a balloon.

3. Tape four strings to the bottom of the balloon. Use playdough to attach the other end of the strings to the table.

4. Turn the hairdryer on as slow as possible. Point the mouth of the hairdryer upwards towards the opening at the bottom and turn the switch on. The balloon will slowly grow in size and pull the cord tight and off the table.

2, homemade wall hanging baskets

Materials and tools: two Sprite bottles, glue, carving knife, scissors.

Methods:

1. Remove the green bottom set of a Sprite bottle, cut it into a lotus shape, turn it down and glue the bottle into a base.

2. In the green bottom set intercepted 2 cm wide green ring, still set on the bottle.

3. Remove the neck of the bottle, cut out a 13 cm long and 8 centimeters wide wide band on the bottle, and a number of 3 cm wide narrow band.

4. Use a carving knife to carve a pattern on the 3 cm narrow strips? As in Figure 3, then fold these narrow strips outward and insert them into the green ring from the bottom up.

5. Take another beverage bottle and, using the bottle, cut out six 17 cm capsule leaves with scissors.

6. Nail the basket to the wall, insert the leaves and flowers, and the wall-mounted basket is made.

3, homemade soap paper

Making materials and tools:

Moisture-absorbent white paper, small pieces of soap, a brush and disposable beverage cans.

Methods:

First, the soap is chopped and placed in the can, the right amount of water and put the cup on the stove to heat up the soap melting, cut the white paper into a matchbox size, a sheet coated with soap, and then remove the drying of the soap paper.

4, homemade flashlight

Specific production methods are: a waste cans (such as Lulu beverage cans) up off one end of the lid, the other end of the round hammer knocked concave. Use thick corrugated cardboard to roll up two batteries, the battery positive side up, negative side down into the can. Find a suitable plastic lid (e.g., a magical large rolled box lid will snap right onto the Lulu beverage can), and dig a small round hole in the center of the lid, the size of which is appropriate to allow the light bulb to be inserted tightly. Insert the bulb base into the hole. Take a piece of wire and strip the ends of the wire, wrap one end around the base of the bulb, and pierce the other end through a small hole in the side of the plastic lid. Place the plastic cover over the can. Check to see that the bulb and battery are not in close contact. Here the disposable flashlight is ready. When using, use your thumb to put from the side wall through the wire pressed from the cans without paint on the weld, the flashlight will glow, thumb away from the wire jumped up, the flashlight will go out, the use of very convenient.

5, clean eraser with brush

Write the wrong word, use the eraser. After erasing, the paper will always leave a lot of debris. Whether you use your hand to shoot or blow with your mouth, it's unhygienic and troublesome. Making a clean eraser won't be such a trouble.

Materials: large eraser, waste brush.

Tools: scissors, glue.

Methods:

1. In one end of the eraser dug a shallow small round hole

2. to the waste of brushes removed from the pen, washed and dried.

3. Cut off the tip of the brush head to turn it into a small brush.

6. Make a pen holder!

Do you have any unused glasses at home? Or dropped the handle of the teacup or something, try, as long as heavy enough to put the pen can be. Find a piece of beautiful cloth, or colored paper, to the cup to do a piece of clothing. Kraft paper is also good, wrap it around the cup and measure it, cut out the right piece, leaving an extra centimeter or so at the joints. Get some glue, glue, all-purpose glue, and stick the jacket to the cup. Chewed gum will also work, the gum should be tugged a little smaller, the important thing is to get the borders and joints tightly attached. That's pretty much it, trim the not-so-neat areas, stick a random decoration on it, color pencil a few words, and you're done.

No decorations? Get a pictorial and cut some pretty ones down, little ribbons that fall off clothes or something, or just paint them on.

4. Nestle the tip of the brush into the small round hole of the eraser and glue it in place

Okay, the clean eraser is made. Whenever you finish erasing the eraser, you can use a brush to gently "sweep" the paper debris together, and then poured into the waste paper basket.

6, the production of tumblers

Methods

[Materials]: table tennis, rubber balls, white latex, shredded cloth or shredded confetti, playdough

[Production process]

(1) will be the top of the rubber ball to open a 3-centimetre-diameter holes, from the mouth of the ball to the bottom of the ball into the equivalent of one-third of the ball or so of the rubber to do not fall over the body of the body. .

(2) Use white latex to glue the ping-pong ball to the small round hole in the rubber ball to make the head of the tumbler.

(3) Use cloth corners or colored paper to cut out the five senses and limbs of a tilting doll and attach them to the head and body respectively.

Method 2

[Materials] Rice, bowl, chopsticks, toilet paper, egg

[Process]

(1) Poke a hole in the top of the egg with chopsticks, use chopsticks to stir up the egg white and yolk, and let the yolk and the egg white flow into the bowl, rinse with water, and dry with toilet paper.

(2) Pour some rice into the small hole you just poked in the egg, and pour some glue to hold the rice in place at one end inside the egg.

(3) Made a little round hat out of colored paper.

(4) Glue the little hat onto the hole at the top of the egg.

(5) Draw a face, eyes, nose, and mouth for the undefeated egg.

Method 3

[Materials]Cardboard sheets, ping pong balls, steel or glass balls, colored pencils, art knives, latex

[Making process]

(1) Make a cylindrical drum from the sheets.

(2) Split the ping pong ball flat into two halves and glue one half to one end of the cylinder first.

(3) Assemble the body of the baby panda by placing a steel ball or a glass ball (the steel ball or the glass ball can roll freely inside) in the cylinder, and then glue the other half of the ping-pong ball to the other end of the cylinder.

(4) Draw your favorite animal head on the outside of the cylinder.

A little animal that can turn over its heel is made, put it vertically on a page, push it gently and it will turn over its heel and go forward