Before using the binding machine, you must check whether the photocell of the binding machine component is in good condition, whether the reflector is aligned and whether there is dust on it. If it is not aligned, please align it to the correct position and remove the dust from it. Whether the screws and nuts of all parts are loose and tightened in time. If there is any leakage of nails and caps, the repairman must be informed to deal with it in time. Check the belt feed track for any debris blockage. If there is, it must be removed, and then the dust in the belt feeding track must be blown clean with compressed air.

Check whether the crankshaft is short of oil. If so, the crankshaft must be oiled by impregnation. Usually a small stick is dipped in oil and slowly drips on the shaft. Can't flow backward into the belt feeding track, it will slip when touching the belt, and it won't close the belt and tighten it. If you find any abnormal phenomena during startup, such as loud noise, large vibration, peculiar smell, etc., if you can't find them yourself, you should stop the automatic strapping machine and call a repairman to deal with them, so as not to damage the internal parts. In addition, it also provides the use and maintenance of vacuum packaging machines, binding machines and shrinking machines. In the production process of binding tapes, due to the influence of incoming material density, equipment failure and human factors, the specifications of binding tapes are unstable after manufacture, and the following situations often occur: uneven thickness, uneven width and rough surface. So that the tape can't be fastened, the tape can't be fastened, and the tape gets stuck in the packaging process. It directly affects the progress of production and the downtime rate of packaging group. The usual treatment method above is to check whether it is equipment or belt. When it is confirmed to be a belt, if the thickness is uneven, the width is uneven. , is the quality problem of the binding belt. Unqualified short sections should be cut off and not used. In the trial run, if the belt can be punched but not tight, adjust the elastic button on the strapping machine until the adjusted belt meets the technical standards.

The unstable quality of the binding tape of the binding machine will also lead to the difficulty of feeding the tape, or the inability to feed the tape directly, and even cause the binding tape to be blocked. If most tapes don't meet the quality standards, then change to a new one for audition. In production, cigarette packs run directly without being punched, or one of them is not punched. Check whether the photocell and reflector are aligned. If not, please align them. If there is any damage, you should inform the electrician to replace it. When the cigarette packet reaches the position where it should be tied, it should not be tied. The treatment method is to check whether the temperature regulator of electric soldering iron is at the required temperature position, usually the temperature is 300C C, which can be appropriately adjusted between positive and negative 10C according to the ambient temperature.

If the temperature of the binding machine is too high, it will break easily after ironing, and if the temperature is too low, it will not stick to the belt. Check whether the belt feeding track is loose. Generally, if the nut falls off, the belt feeding track will cause the belt to slide sideways, which will not reach the standard position, resulting in the inability to drive the belt. Cassette is also a common problem. During the boot process, due to improper operation or unqualified tape, the tape will get stuck in the tape feed guide. Therefore, it is necessary to remove the tape blocking plate next to the tape feeding track, take out the adhesive tape stuck inside, and blow off the remaining binding tape and dust with compressed air.

Replace the binding tape calmly and smoothly. When there are 2-3 bundles of binding tape, take the binding tape off the binding tape rack and put it aside, which is beneficial to have a certain time to replace the new binding tape without affecting the normal production. After changing, put the tapes in order, and put the rest of the previous tape out. Generally, the last tape shall prevail. Practice economy and put an end to waste. Then put on a new strap to complete the strap changing process. When replacing a new belt, there will be uneven tightness, and the tightness button should be adjusted in time until it meets the process standard. Moderately adjust the binding tape, too tight is easy to bind, too loose does not meet the technological requirements. It must be adjusted to meet the process standards to ensure the success rate of tape release.