1. Create a new A4 page with RGB color mode and landscape orientation. Double-click the rectangle tool to draw a rectangle with the same page size, press F 1 1 to fill the gradient ellipse ① # 3d0f7a2a2 # 7d14ae3 # c3164b4 # feb715, and press g to adjust the gradient.
2. Enter the text with the font of Founder Zheng Da black simplified, and enlarge it with the selection tool. Click on the menu bar object to break it up, or press ctrl+k to split the calligraphy and adjust the text size, as shown in the figure.
3. Draw with Bessel tool and press C to control the lever. Put it in the position shown in the figure.
4. Select the Star Tool, pull out a star in the page, and enter the number of edges 5 and sharpness 53 in the property bar. The effect is shown in the figure below. Pull out the desired effect with the shape tool, as shown in the figure.
5. Click the selection tool, shrink the stars, hold down the shift key, and right-click to copy one. As shown in the figure. Select these two shapes, select the previous object in the property bar, copy three, resize them and place them in different locations. As shown in the figure.
6. Select all the objects in the box, select the combination of attribute columns, fill in # 6262F6 and make a copy and put it aside for later use.
7. Select the stereo tool. Select stereoscopic in the preset of the property bar, and change the stereoscopic color from #FDDD03 yellow to orange # e18501in the property bar; Set the vanishing point coordinates X:0MM, y:-/Y:- 175.864mm；; The depth is 5,
8. Put another copy on it. In the tool selection mode, find the contour tool in the toolbar and select the external contour in the property bar. The contour offset is 5 mm; Suitable until; The fillet of the contour is mitered, and the filling color is # d 31415; Fill the color inside with red, and then press ctrl+pagedown to go to the next floor;
9. Make a three-dimensional effect for the bottom layer, change the color from #FFF200 to #FF7700, and change the depth in the property bar to 10. Turn off the lights, the effect is as shown in the figure.
10, select the above three-dimensional characters, select the objects to be divided into three-dimensional groups and add gradient colors on the top layer, and press F 1 1, and the color value ① # 86117d2 # be1565438 ③ #.
1 1. Split the three-dimensional text into three-dimensional groups, and press F 1 1 to add gradient colors, ① # 6e0309 ② # 870e12③ # da1721. Press g to adjust the color, as shown. Location.
12. press CTRL+C and CTRL+V to copy one in situ. Select the contour tool, and select the internal contour with the contour offset of1.5mm.. Select the object to split the profile group. Then fill the interior with white, and the effect is as shown in the figure. Then import materials, balloons and gifts, and starlight.
13. Draw an ellipse, fill it with black, remove the outline, add transparency, and the ellipse gradually becomes transparent. The effect is shown in the figure.
Cdr Poster Making Tutorial If the whole poster is a vector diagram, you can reduce it first and then enlarge it. If there is a bitmap in the poster, it is recommended to make it according to the original size.
Really not line, also can be like this:
1) If inkjet is directly output in CDR, reduce the pixels of bitmap in PSD and put it in CDR for effect. When the effect is finished, replace the original small picture with the big picture. (The vector diagram part can be minimized)
2) If it is exported to JPG inkjet printing (the export is generally CMYK four colors), it is necessary to reduce the original image by 80%, not too small to be afraid of blurring. When exporting, put 300DPI in the pixel input. The differences between the exported images are very small. It should be noted that when drawing for others, you must tell the size, because the exported bitmap may become larger! ! (If you are worried about blurring, you can import the exported graphics into CDR and adjust it to 100%. There is an enlargement of 1: 1 in the CDR, and it can be seen that the printing effect mode is not blurred. Or afraid of blurring, just paint that part. )
It doesn't matter if it's a little fuzzy, because such a big poster will usually be seen from three meters away, and no one will gather in front to see it.
How does CorelDraw make a poster to promote the inner page/album? When you see the poster above, you must first understand some basic information and layout of the pictorial. The size of the inside page of this poster's album is 2 10* 150mm, so first open the CDR software to create a new canvas with the size of 2 10* 150. Because of printing, the bleeding size is reserved. Draw one on the canvas with the rectangle tool.
After the big box is built and divided into several local blocks, you can add content to each rectangular area. First, you can fill in the big page. At this time, when filling the blue sky and white clouds scene, the precise cutting tool of the picture frame (the effect-the precise cutting tool of the picture frame-is put in the container) is generally used, as shown below.
Pictures can be placed or dragged to appear in the CDR. The following steps have been completed, such as color filling, picture placement, logo placement, and border precise cutting tools, as shown in the figure.
Let's see if we have completed a general outline first, and then the details. First, starting from the car steering wheel in the upper left corner of the picture, we need to use rectangular tools, change the angle, drag and copy the rectangular tools to speed up the progress of picture completion, and also involve text tools, superscripts and subscripts. , as shown in the figure below.
In addition to using superscript, the text on the poster also involves the text deformation tool, that is, the "shape tool-shape" in the toolbar and the shortcut key CTRL+Q are used to convert it into a curve tool to adjust the text for 24 hours, as shown in the following figure.
In addition, it also involves line tools. When everything is involved, don't forget to remove the edges of all rectangular boxes in the picture. At this time, the problem involved is how to remove the edge box with one click, as shown below.