3. mesh
4. Shape two slender circles and twist them clockwise twice at the tail.
5. Draw two circles into the shape of the butterfly's front wings.
6. The two front wings are tied together.
7. Tie the last two parts together.
8. Wrap with paper tape
9. Adjust the shape of the front fender slightly.
1 1. Wind the electric wire on the adhesive tape, and then tighten the electric wire.
12, cut off the extra wires.
13, slightly bending the metal wire into two whiskers.
14. After the butterfly is finished, you can put a pin on the tape and a butterfly pendant will be finished.
And:
One. Materials and tools
(l) Colored metal wire, with many colors and models.
(2) elastic screen, with a variety of monochrome and bicolor.
(3) The flower cores have various shapes and colors. Self-adhesive tapes come in various colors.
(5) synthetic fiber thread for sewing.
Cotton. (7) White glue for carpentry.
(8) Quick-drying adhesive.
scissors
(10) Pointed pliers.
(1 1) wound casing with a diameter of 8CM from ICM. It can also be replaced with cylindrical articles such as milk bottles and refills.
Second, the basic steps
Winding, barbed wire, assembly and modeling are all for making silk screens.
Four basic steps of flower cultivation.
(1) hover
In the process of making petals, receptacles and leaves, colored metal wires need to be wound into a circle first, just like their skeleton frame. For larger petals, leaves and receptacle, it is necessary to make them piece by piece, and the winding method is single winding method, while for smaller petals, leaves and receptacle, multi-winding method can be used, so that a multi-petal skeleton can be completed at one time. Some special flowers and leaves need to be tied in multiple knots. Petals and leaves with veins need to be tied first, and then veins are formed.
(1) single winding method
① Wrap colored metal wires on the casing 1 turn, and the ends of the metal wires are crossed.
(2) At a position about 5 mm away from the surface of the sleeve, clamp the staggered place with fingers or pointed pliers and tighten it, and then rotate the sleeve longitudinally for 3-4 times.
③ Cut the wire at the end of winding or leave a 2-5cm wire at the root of the coil.
（2）
The wire was bent by 5 cm.
(2) Hold the elbow by hand and wind the long end of the wire around the sleeve.
③ Continue winding for 3-6 times.
(4) Merge four iron wires outside the circle.
⑤ Clamp and tighten the four wires, and then rotate the sleeve longitudinally for 3-4 times.
⑥ Cut loose wires or leave two wires 5 cm long.
③ Multi-stage winding method
① First, complete the winding method of single coil and change the coil into the required shape.
(2) Continue winding the rest of the wire, just like the figure of eight. The diameters of the upper and lower coils can be different as required.
(3) Three parts can be completed in the same way, and the size of each circle changes as needed.
(4) Wave circle method
① First, the colored metal wire is wound on the knitting needle.
② Remove it from the needle and stretch it.
(3) Then circle, which is the same as the single circle winding method.
5] Preliminary draft
After winding, the skeleton is round. According to the basic shapes of petals, leaves and flowers in the work, knead the required shapes by hand. Multi-winding method is formed as follows.
(1) Multi-turn kneading together.
② The coil is open.
③ Adjust to a proper position.
② mesh
(1) single-ring grid
(1) Put the wire mesh evenly on the metal ring.
② Pull to the root of the circle.
(3) After winding the wire several times at the root of the circle and binding it, directly pull the wire off. (4) Free modeling after completion.
② Multi-section grid
(1) with a single ring network.
② Screening and ligation.
(3) Cut off the redundant screen.
(4) Hold two circles with both hands, twist one circle at the intersection of the two sections, and then you can shape freely.