1, internal head connection

Figure 1 is a good way to tie a knot, but this knot is difficult to tie.

Knotting step: (1) lap two thread ends together, first wrap one thread around the other thread for four times, pull the thread ends back and pass between the two threads; (2) Winding another thread for four times according to the method in step (1); (3) Insert two threaded ends into the middle threaded hole and tighten both ends.

Connecting in this way, like all fishing line knotting methods, the node strength of thin line is low, and the node strength of thick line is high. For example, the nodal strength of 0.2 is about 75% of the linear strength; On the main line 1, the nodule strength is about 95% of the straight root strength; The more lines, the stronger the nodule.

Like all knots, the same thread and the same knotting method will directly affect the tensile strength. The key to making a good knot is to straighten out the lines in the knot and not to have too many entanglements.

2. External connection

The knotting method in the figure is simple and easy to master, but the nodule strength is only about 68%.

Knotting step: (1) overlap two threads together. First thread the left thread on the right thread, turn around four times, then thread it in the coil and tighten it slightly; (2) Wind the wire on the right side four times, and then tighten it slightly; (3) Tension at both ends.

3. Inner ring connection

The knotting method in the figure is simpler, and the node strength is also high, but the two ends of the knot are not in a straight line, and the two ends are slightly bent, as shown in the figure. In this way, the joint strength of 1 line reaches more than 92% of the straight line strength.

Knotting step: (1) Overlap two thread ends together, loosen one long thread end and one short thread end, thread the other long thread end back into the wireframe, and thread the one long thread end into the wireframe like a knot; (2) Go back and thread two lines, one long and one short, into the wireframe, and so on for four times; (3) The line on the right is also wound around four times and then slightly tightened; (4) Both ends are gradually tightened.

Note: When tightening, pay attention to the fact that both lines should be stressed at the same time, as evenly as possible. This is the key to ensure the quality of knotting.

Step 4 connect the two ends

The knotting method in this picture is also often adopted by fishermen. In this way, the maximum knotting strength can reach 85% of the straight strength, and the two ends of the knotted thread are relatively straight.

Knotting step: (1) overlap two threads together. First, thread the left thread on the right thread. After turning back, make five turns from the circle, and then tighten slightly. (2) Wrap the wire on the right side five times, and then tighten it slightly; (3) Tension at both ends.

Second, the loop knot

1, inner winding ring junction

The picture shows the inner winding loop knot. This knot can form a fixed ring at the end of the fishing line to connect other fishing tackle, which is often used at the end of the main line of throwing rod. Tie the knot as shown. The maximum strength of nodules can reach 96% of the straight strength, and the knotting method is simple.

2. Outer winding loop knot

The picture shows the outer winding loop knot. As shown in the above figure, the inner loop knot can form a fixed loop at the end of the fishing line, and the maximum strength of the knot can reach 96% of the vertical strength. The way to tie a knot is simple.

Third, the connection between the wire and the ring fitting.

1, it is best to connect the main line with the 8-character ring.

As shown in the figure, this kind of knot is often used to connect the main line and the figure 8 ring. This knotting method, the maximum node strength can reach 99% of the linear strength, and the knotting method is simple, even if it is not properly knotted, it will not seriously affect the node strength, so it is a very recommended knotting method.

2. The traditional sub-line is connected with the figure-eight ring.

This knotting method is often used to connect the sub-wire and the figure-eight ring, and the maximum knotting strength can reach 97%. When knotting, winding and pressing the thread, the thread must be placed "smoothly". After knotting, the knots should not be piled up, otherwise the strength of the nodules will be seriously affected.

3. The best sub-lines are connected by 8-shaped rings.

As shown in the figure, this knotting method is the simplest, and the tensile strength of nodules is also the largest, reaching 99%. The principle is the same as "connecting the main line with an 8-shaped ring".

Fourth, the connection between the main line and the pole tip.

The knot of fishing line varies from fishing line to fishing line. Two knotting methods of main line and the connection method between main line and pole tip.

Different fishing lines tie different knots and have different tensile strength. The two knotting methods in the picture are the most commonly used methods to connect the main line of the hand rod with the tip of the fishing rod. For most good threads, the upper knot method is strong and the lower knot part is strong. When using strange fishing lines, it's best to do a comparative test to see which knotting method is more powerful. We can also roughly judge the quality of the fishing line according to the knot of the broken line: generally speaking, if the knot above is firm, this line is likely to be a better line.

Generally speaking, it is recommended to use the 8-knot knotting method in the above picture for fishing lines with better quality.

Verb (abbreviation for verb) Connection of fishing line and hook connector

The connection method in this figure can keep the fishing line strength at the highest value. With this connection method, whether it is a thick line of 1 or a very thin line of 0. 1, the strength at the knot can reach more than 95% of the vertical strength. This knot doesn't need to be cut after taking off the sub-thread, so it can be used again next time. When the fish situation is unknown, or the fish situation changes greatly, and the auxiliary line needs to be replaced frequently, the waste can be reduced.

This is a very recommended way to tie the secondary line for competition. Especially in the use of super-strong thread, because it highlights the characteristics of high strength, the thread quality is hard, and this knotting method can completely solve the shortcoming of slightly lower nodule strength.

This is a very recommended way to tie the secondary line for competition. Especially when the fishing line with high strength and hard thread is used, this knotting method can completely solve the disadvantage of slightly lower nodule strength.

It is particularly important to note that when using this single hook swivel, it is necessary to clamp the hook mouth with pliers, and it is best to try it repeatedly, so as to prevent the auxiliary line from falling off during fishing and reduce the possibility of hooking the single hook when the auxiliary line falls down.