Question 1: How to operate the end of the nail bead? The ending is a knot, but the fishing line will loosen after a long time. Beads are usually beaded with thin fishing line, and the method is as follows: (It's much more complicated, so it's very simple to try. )

Several commonly used string methods:

Single-line knot method of lock head

Thread the thread through the lock and the other end through a small bead and tie a knot.

2. Tighten the thread toward the lock head, wrap the beads in the lock head, and clamp the lock head with pliers.

Locking double knot method

1. Thread two wires through the lock and tighten them.

2. Clamp the lock with needle-nosed pliers and press hard.

Special treatment method

1, string the wrong beads-just crush them with needle-nosed pliers when wearing the wrong beads, wrap them in cloth or plastic bags and crush them again.

2, burning line method-burn the line into a ball with a lighter, and it is not easy to fall off with white glue.

Question 2: Single-thread beading and how to tie a knot. Specific steps:

1, find a towel and spread it to prevent the beads from rolling around. Fold the crystal line 1 4 (beads only need 1 2) and put the copper wire or fishing line 1 2 on your head.

2. Take the fishing line as the guide and start to wear beads. First, find a bead with big eyes to wear, so that the knot can be retracted into the bead in the future.

3. All dressed up. Pass the 2 strands of rope on the right through the 2 loops on the left.

4. Move the beads to the top of the left rope, 2 or 3 at a time.

When all the beads are taken out, they must be close together, leaving no gap.

6. Pull the rope on the left so that the two beads are in close contact.

7. Tie two or three knots between the two ropes on the left and the two ropes on the right, and pull the rubber band after each knot. Then cut off the extra rope, leave some rope ends, and don't cut the knots, then all the previous efforts will be in vain.

8. Pull the knot into the bead on the right (that is, the first one to wear), finally tidy it up, and make the bracelet even and round, and you're done.

Question 3: How to tie cross-stitch beads? 1. Embroidering beads requires two embroidery threads.

2. Fix the beads on the embroidered cloth by half stitch method.

3. Then take the needle out of the hole it started to pass through (just in the lower left corner of this grid).

4. Separate the two strands and bypass both sides of the beads.

Step 5 pass through the oblique hole

This bead is firmly fixed on the embroidered cloth, and it is also tight by hand.

Question 4: Q: How to tie the elastic rope of the bracelet? You can tie a Chinese knot, or you can tie a double button like a shoelace, or you can string small beads like crystals and tie a fast knot. Personally, I prefer to tie my shoes.

Question 5: How to tie the elastic rope of the bead bracelet?

1. First, pair the ropes into the following shapes.

Step 2 pinch out the right shape

3, according to the direction in the figure and number order, knot.

4. The effect of playing for the first time.

5. Tie the knot for the second time according to the method just now.

6. Tie the knot for the second time according to the number and sequence shown below.

First of all:

Second:

Third:

Fourth:

accomplish

Question 6: How to tie the 2mm fishing line for beading firmly? It is suggested that lz should not cut the fishing line immediately after knotting. Reweave the remaining fishing line into a three-dimensional little thing. Don't worry about boating. I did it.

Question 7: How to Knot the Knot at Hand Steps at Hand (Take elastic beading as an example):

1, this shape.

2. tie the knot according to the picture.

Turn it over and try again in the same way.

4. Turn it over again and tighten it in the direction indicated by the arrow.

5. The organization is as follows.

6. finished products.

Question 8: How to tie the beaded bracelet of1?Tie it with the usual knotting method (it must be tied twice or more), but it must be tied tightly, and finally the thread is hidden.

2. Take a locating buckle, and both the left and right wires pass through the locating buckle. Finally, clamp the locating buckle with pliers.

Question 9: How to Knot Tibetan Bodhi Beaded Rope It is suggested that the best choice for Tibetan Bodhi Beaded Rope is to tie a diamond knot, followed by a snake knot. Specific method Baidu diagram.

Question 10: Why is the rope of the bead bracelet knotted on the arm? DIY Handicraft Club related search crystal bracelet knot method, DIY Handicraft Club. There is always a problem with the knotting of the bracelet with crystal elastic string, either the knot is too big to hide the bead hole or it is opened too hard. I don't know what to do. Please give me some advice. Thank you! Crystal Beads View Original Post >>